manualshive.com logo in svg

Bolin Technology BC-7-4K20S-S6MNB, User Manual, Page: 13 / 59

Share
Download
Bolin Technology BC-7-4K20S-S6MNB User Manual Download Page 13

13 

 

Power 

•

 

Use only the DC power adaptor (JEITA type4) supplied with the unit. Do not use 
any other DC power adaptor. 

•

 

If using POE to power the camera, PoE+(IEEE802.3bt) is supported 

•

 

Ensure that the POE power source has sufficient power budget to power the camera, or some features 
may not function properly  

•

 

You can use One-Cable POH (Power Over HDBaseT) power up the camera via CAT6 cable when 
HDBaseT video card is used. 

•

 

 

Cable Requirements  

•

 

Network Cable:

 10/100 Mbps Ethernet CAT 5/5E/6 UTP cables are applicable to the ANSI/EIA/TIA-

568A/B and ISO/D. Eight wires in the network cable need to be inserted in parallel into the top of the 
cable connector. The cable connector needs to be crimped in position. When the cable connector is in 
position, ensure that the metal pieces of the cable connector are parallel to each other and the clamp 
of the cable connector is intact.  

•

 

SDI video cable: 6G-SDI

 

o

  Belden 4694R/RG-6/U is a suitable cable to transmit broadcast-quality video: 

 

•

 

SDI video cable: 3G-SDI

 

o

  Belden1694A/5CFB is a suitable cable to transmit broadcast-quality video: 

 

Summary of Contents for BC-7-4K20S-S6MNB




























































Reviews:

No comments