background image

Troubleshooting

10

Amplifier will not turn ON.                                 Check the fuse.  Replace fuse only with same type and rating.

                                                                            

No output on WMT1A and                                 Make sure that the speaker output GND/COM shorting clip
Power Amp Outputs                                          is in place.

No telephone output.                                         Make sure that the MIC 5/TEL switch is in the TEL position.

                                                                            Make sure the VOX control is set properly

                                                                            When connecting the telephone Tip & Ring, make sure to use 
                                                                             the two outside terminals and not the center terminal (GND).

AUX input will not mute with                            Check that the VAR MUTE control is not set to 4 (0 dB).
telephone page.                                                  This control adjusts the level of the background music 

                                                                            when making a page. See page 9.

Microphone squeals or hums when                Check your wiring connections for the 3-pin connector. 
using the 3-pin connectors but not                  Pin 1 is the shield connection. Pins 2 and 3 connect
when using screw terminals.                            to the balanced signal leads on the mic cable.

Condenser MIC will not work.                           Make sure that phantom power switch (MIC 1 - 4) is on. 

                                                                            See page 4.
                                                                            
                                                                            MIC 5 and 6 use circuit board jumper. See page 5.

Telephone input cuts off the music,                Adjust the VOX control on the rear panel to eliminate any 
when not making a page.                                  unwanted noise that may be triggering the VAR MUTE circuit.

                                                                            See page 9.

Telephone input is choppy or                          Adjust the VOX control counterclockwise to make the 
cuts off the beginning of a page.                     trigger activate at a lower input signal level. See page 9.

The telephone page volume is too

Adjust the ALC control on the rear panel. See page 9.

loud on some pages.

AUX 1 input not working

Make sure MIC 6/AUX 1 switch is in the AUX 1 position.

Make sure the signal source is plugged into the AUX 1 
RCA jack.

Summary of Contents for Gold Seal Series

















Reviews: