manualshive.com logo in svg

BodyCraft BCG-GX, Instruction Manual, Page: 15 / 21

Share
Download
BodyCraft BCG-GX Instruction Manual Download Page 15

14

STEP 8  INSTALL  LOWER  CABLE

1. Route the steel ball end of the Lower cable (89) under Pulley L1 mounted at the front of the Low Pull 

Station using one 3/8" X 1-3/4" Hex Bolt (101) and one 3/8" Nylon Nut (124).

2. Continue back to Pulley L2 mounted on the Base Frame (1) using one 3/8" X 1-3/4" Hex Bolt (101) and 

one 3/8" Nylon Nut (124).  Route the cable underneath L2 and then up to Pulley L3 mounted in bottom 

of the Double Pulley Block (19) using one 3/8" X 1-3/4" Hex Bolt (101) and one 3/8" Nylon Nut (124).

3. Continue down to Pulley L4 mounted to the Base Frame (1) using one 3/8" X 1-3/4" Hex Bolt (101) and 

one 3/8" Nylon Nut (124). 

4. Route the cable underneath L4 and Pulley L5 mounted in the slot in the bottom of the Front Upright (3) 

using one 3/8" X 3" Hex Bolt (99), two 3/8" washers (116), two 3/8" ID Bushings (77), and one 3/8" 

Nylon Nut (124).

5. Connect the steel ball end of the cable to the receptor bracket L6 welded to the Leg Extension Arm (10).

Summary of Contents for BCG-GX






















Reviews:

No comments