background image

������

 

 

SAFETY AND CAUTION

Before Using Read All The Warnings And Obtain Instruction On The Use Of This Machine!  Use 

Only For Intended Exercise!  DO NOT Modify The Machine!

Before Beginning Any Exercise Program, Consult With Your Doctor Or Health Physician.

Refer To The Manual Whenever You Have A Question.

Keep All Body Parts And Clothing Free From All Moving Objects And Parts Of This Machine!

Always Use A Spotter When Attempting To Workout.

If The User Needs More Assistance, Please Contact A Technical Consultant Before Attempting To 

Use The Machine.

Keep Your Fingers, Body Parts, Children And Pets Away From Moving Parts.

Warm Up Before Each Workout And Cool Down After Each Workout.

Do Not Allow Children Near This Equipment!  Teenagers Must Be Supervised!

Inspect The Machine Before Each Use, Make Sure All Of The Connections Are Tightly Secured.

Do Not Over Tighten The Bolts Or Screws As It Could Result In Bending The Steel Or Plastic.

Inspect The Machine For Tears And Broken Welds And Make Sure To Do Routine Maintenance On 

The Unit Before Use.

If The Parts In The Box Does Not Match The Owner’s Manual, Please Do Not Assemble And Contact 

The Customer Service Department Immediately For Assistance.

If The Machine Is Not In Proper Working Condition As The Above Points, 

Please Do Not Use The 

Machine.

This Product Is For 

Consumer User Only

And It Is Not Meant For Commercial Use.

If The User Does Not Follow These Warnings, It Could Result In Serious Injury Or Even Death.

The Minimum Suggested Clearance For Safe Exercise 

7’ Long 7’ Wide

.

W A R N I N G

W A R N I N G

SAFETY AND CAUTION

Summary of Contents for WB 125
















Reviews: