background image

11

EN

3.2  INIT mode

The INIT mode allows for carrying out the pairing between the clock to be synchronised and the 

DHF transmitter. It is activated as factory default, when the clock switches on until it is paired with a 

transmitter.
To connect the clock with the transmitter or another transmitter, press the INIT button for 5 seconds 

to set the clock in INIT mode. 

This operation can be done at all times after setting the hands at noon for the first 

time, when the clock switches on.

Activating the INIT mode is only useful when changing the DHF transmitter (as well 

as the channel). 

•  Clock behaviour: 

When the clock is brought into service (when it switches on) or during the activation of the INIT 

mode, the hands are set back at noon and the product switches to radio listening (synchronisation 

process with the DHF transmitter) 

only if the clock has enough power to do so.  

If this is the case, 

the clock will be set on time.

•  Behaviour of the orange INIT LED: 
The INIT LED indicates that the INIT mode has been activated and that the DHF INIT listening 

windows are open. 

Refer to the diagram below to interpret the status of the INIT LED according to the status of the 

clock:

Synchronisation 

successful?

Starting the clock 

(commissioning) 

Status of the clock

Reset of the hands 

The LED switches on

Opening of a listening 

window for synchronisation 

with the DHF transmitter

The LED switches 

on for 11 seconds 

at most  

The LED flashes 5 times 

and switches off

Set on time 

INIT mode activated

(by pressing INIT button)

The LED switches 

on immediately 

The LED switches on 

after 5 seconds 

Status of the INIT LED 

1 minute waiting time 

(

repeated cycle until 

synchronised with 

the transmitter

)

OR

OR

The LED switches off 

for 1 minute 

If the INIT LED has not been activated when the clock switches on (commissioning) 

or if it is definitely deactivated after the hands have been reset at noon, or during 

the synchronisation search cycles, then the clock no longer has enough power. In 

that case, it is recommended to charge the clock via USB and choose a location with 

better light exposure if necessary. 

Summary of Contents for Profil 930 L

























Reviews: