manualshive.com logo in svg

Bobrick AirCraft B-701, Troubleshooting And Information Manual, Page: 54 / 66

Share
Download
Bobrick AirCraft B-701 Troubleshooting And Information Manual Download Page 54

Page 4 

INSTALLATION INSTRUCTIONS BOBRICK ECLIPSE

®

 

SURFACE-MOUNTED HAND DRYERS 

 
 

Electrical Characteristics: 
 

Models  B-740  (Vitreous  enamel  cover),  B-748  (Chrome-plated  cover),  115V  AC,  20  Amp, 
2300 Watts, 50/60Hz, Single Phase; UL/c-UL Listed; cULus Listed. 
 
Models B-740 (Vitreous enamel cover), B-748 (Chrome-plated cover), 208

–240V AC, 9–10 

Amp,  1900

–2400  Watts,  50/60Hz,  Single  Phase;  VDE  Approved  and  CE  marked,  cULus 

Listed, and CCC approved. 
 

REMOVAL OF COVER 
 

Start installation of dryer by removing cover. Loosen single cover-locking screw located in 
recess in the air inlet/outlet grille using a Phillips-head screwdriver. 
 
To remove cover, place a hand on each side of the cover and tip the bottom away slightly 
from the air inlet/outlet grille. Lift the cover upwards to release the top retaining bracket from 
the mounting base. 
 

INSTALLATION OF MOUNTING BASE 
 

An Installation Template is supplied with each unit. 
 

 

 

Summary of Contents for AirCraft B-701



































































Reviews:

No comments