manualshive.com logo in svg

Bobrick AirCraft B-701, Troubleshooting And Information Manual, Page: 11 / 66

Share
Download
Bobrick AirCraft B-701 Troubleshooting And Information Manual Download Page 11

Page 5 

      

 

 

 

Warning 

Risk of electric 

shock 

Disconnect power 

supply before 

removing cover 

Instructions For Removal Of Dryer Cover 

 

To Remove Cover 

Locate the two tamper resistant screws at the bottom of the dryer cover. 

Using the Allen-wrench (4 or 5mm), turn the screws 

clockwise

 to loosen the cover. Do 

not take the screws out, the screws have to be moved / rotated up to loosen the cover. 

Lifting the cover over the two latches at the top of the chassis, remove the cover. 

 

To Replace Cover 

Place the cover over the two latches located at the top of the chassis. Make sure that 
the cover has a good  fit. 

Using the Allen-wrench, turn the screws 

counter clockwise

 moved/ rotated down which 

will tighten the cover onto the chassis. 

Do not

 over tighten screws. 

Check to make sure the cover has a good fit. Turn power back on to the dryer unit. 

 

 

 

Summary of Contents for AirCraft B-701



































































Reviews:

No comments