manualshive.com logo in svg

BMW Z8, Owner'S Manual, Page: 140 / 175

Share
Download
BMW Z8 Owner'S Manual Download Page 140

140

n

Battery

Fuses 

Return used batteries to a recy-
cling point or your BMW center. 

Maintain the battery in an upright posi-
tion for transport and storage. Secure 
the battery to prevent it from tilting 
during transport.

< 

If an electrical accessory should fail, 
switch it off and check the fuse.

The fuses, their individual ampere rat-
ings and the equipment in the circuits 
they protect are all indicated on the 
cover of the fuse box in the glove com-
partment and on the inside of the cover 
panel for the storage compartment 
located behind the passenger's seat.

In the glove compartment

>

Open the glove compartment

>

Unlock the fuse box and swing it 
downward

>

Remove the lid with the list on it.
Spare fuses and plastic tweezers are 
located in the fuse box lid behind the 
passenger's seat

>

Use the plastic tweezers to remove 
the fuse for the accessory or equip-
ment that has stopped working 

>

Replace a blown fuse, recognizable 
by its melted metal strip, with a new 
fuse that has the same color or 
ampere rating.

520de149

Online Edition for Part No. 01 41 0 156 878 - © 06/02 BMW AG  

Summary of Contents for Z8
















































































































































































Reviews:

No comments