manualshive.com logo in svg

BMW Z8, Owner'S Manual, Page: 126 / 175

Share
Download
BMW Z8 Owner'S Manual Download Page 126

126

n

OBD interface socket 

The Onboard Diagnostic interface 
socket is located on the driver's side at 
the bottom of the instrument panel and 
under a cover. The cover has the letters 
OBD on it.

The purpose of the OBD system is to 
ensure proper operation of the emis-
sion control system throughout the 
vehicle's lifetime by monitoring emis-
sions-related components and sys-
tems for deterioration and malfunction.

520de130

An illuminated indicator informs 
you of the need for service, but 
not of the need to stop the 

vehicle. However, the systems should 
be checked by your BMW center at the 
earliest possible opportunity.

Under certain conditions, the indicator 
will blink or flash. This indicates a rather 
severe level of engine misfire. When 
this occurs, you should reduce speed 
and consult the nearest BMW center as 
soon as possible. Severe engine misfire 
over only a short period of time can 
seriously damage emission control 
components, especially the catalytic 
converter.

Service Engine Soon warning 
lamp for Canadian models.

When the filler cap is not properly 
tightened, the OBD system can 

detect the vapor leak and the indicator 
will light up. If the filler cap is subse-
quently tightened, the indicator should 
go out within a few days.

<

 

Online Edition for Part No. 01 41 0 156 878 - © 06/02 BMW AG  

Summary of Contents for Z8
















































































































































































Reviews:

No comments