manualshive.com logo in svg

BMW Motorrad S 1000R 2017, Rider'S Manual

Share
Download
BMW Motorrad S 1000R 2017 Rider'S Manual Download Page 45

Push switch

1

up to switch on

the high-beam headlight.
Press switch

1

down to oper-

ate the headlight flasher.

Parking lights

Switch off the ignition.

Immediately after switching off
the ignition, push button

1

to

the left and hold it in this po-
sition until the parking lights
come on.

NOTICE

You can switch on the parking
lights within 10 seconds after
switching off the ignition.

Switch the ignition on and off
again to switch off the parking
lights.

Hazard warning lights
system

Switching on hazard
warning flashers

Switch on the ignition.

NOTICE

The hazard warning flashers
place a strain on the battery.
Do not use the hazard warning
flashers for longer than absolutely
necessary.

Press button

1

to switch on

the hazard warning flashers.

4

43

z

Operation

Summary of Contents for S 1000R 2017



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands