BMW Motorrad S 1000R 2017 Rider'S Manual Download Page 157

Page: 157 / 226

Replace the defective bulb.

Bulbs for flashing turn
indicators, front

RY10W / 12 V / 10 W

with LED flashing turn indic-
ators

LED

Bulbs for flashing turn
indicators, rear

RY10W / 12 V / 10 W

with LED flashing turn indic-
ators

LED

Use a clean, dry cloth to hold
the bulb in order to keep the
glass free of foreign matter.

Turn bulb

clockwise to install

it in the light housing.

Working from the inboard side,
insert the glass into the light
housing and close the housing.

Install screw

Replacing bulb for
number-plate light

Switching off ignition (

41).

Pull number-plate light bulb

out of the light housing.

155

Maintenance

Summary of Contents for S 1000R 2017



































































































































































































































Search results

Summary of Contents for S 1000R 2017

Reviews:

Brands by name

Popular brands

BMW Motorrad S 1000R 2017, Rider'S Manual

Search results

Summary of Contents for S 1000R 2017

Reviews:

Brands by name

Popular brands