background image

10

Owner’s manual and assembly instructions:  81000 portable outdoor heater          3/3/03

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Operation

Before Turning Gas Supply ON

Your heater was designed and approved for OUTDOOR USE ONLY.
DO NOT use it inside a building, garage, or any other enclosed area.

Make sure surrounding areas are free of combustible materials,
gasoline, and other flammable vapors or liquids.

Ensure that there is no obstruction to air ventilation.

Be sure all gas connections are tight and there are no leaks.

Be sure the access panel is clear of debris.

Be sure any component removed during assembly or servicing is
replaced and fastened prior to starting.

Before Lighting

Heater should be thoroughly inspected before each use, and by a
qualified service person at least annually.

If relighting a hot heater, always wait at least 5 minutes for gas to
dissipate.

Lighting 

1. Turn Gas Control Knob to OFF position.

2. Push in Control Knob and rotate to “ON” position. This will light

burner. If necessary, keep depressing and rotating Knob until
burner lights.

3. Once burner is lit, hold Control Knob in for at least 30 seconds

and release.

4. If burner does not stay lit, wait 5 minutes and repeat steps 2 and 3.

5. Once burner is lit, rotate Knob to desired heating level.

6. Replace Access Panel.

If you experience any ignition problem, turn off the heater and gas
supply, and consult “Troubleshooting” on page 13.

WARNINGS

FOR YOUR SAFETY: 

• 

Do NOT attempt to operate

heater until you have read
and understand all
precautions in section 1
“Safety First.”  Failure to do
so can result in serious
personal injury, death, or
property damage. 

• 

If at any time you are unable

to light burner and smell gas,
wait 5 minutes to allow gas
to dissipate before
attempting to light heater. 

• 

Do NOT touch emitter or

dome or move heater for at
least 45 minutes after use.

OFF

ON
HIGH

LOW

OFF

ON
HIGH

LOW

Summary of Contents for Endless Summer 81000





















Reviews: