(152)
6
(79)
3 1/8
(356)
14
(197)
7 3/4
(860)
33 7/8
(572)
22 1/2
(1791)
70 1/2
(127)
5
(430)
16 7/8
(44)
1 3/4
(248)
9 3/4
(160)
6 1/4
(457)
18
(1816)
71 1/2
(600)
23 5/8
(57)
2 1/4
(889)
35
L3
L2
L1
UNIT TO THE NEAREST SURFACE
ELECTRICAL CODES.
NOTE: INSTALLATION MUST MEET LOCAL PLUMBING AND
volts to ground.
2. Do not connect to a circuit operating at more than 150
Panel. Check nameplates for voltage and phase.
knockout to terminal block supplied within the Master Control
supply leads (see 'wiring requirements' label) through conduit
1. Final connection is accomplished by bringing proper power
TO WIRE:
3. Connect 1'' drain connection to suitable drain line.
female N.P.T. drains.
2. Models without manifold are supplied with individual 1/2''
one end of the manifold.
discretion of the fabricator. Install and tighten pipe plug in
Model "DM" and "TDM" units. Location of valve handle is at the
1. A drain manifold complete with valve is supplied on all
TO PLUMB:
supplied.
4. Mount Control Panel onto electrical box using screws
12 AWB Cu
FIELD WIRING GAUGE
21.6
15.0
208
4500
MOD-500
AMPS PER LINE 3 PHASE
VOLTS
WATTS
MODELS
SINGLE
12 AWB Cu
25.0
17.0
240
6000
MOD-500
12 AWB Cu
29.8
19.5
208
6200
MOD-500T
12 AWB Cu
34.4
22.1
240
8250
MOD-500T
11.2
13.0
14.6
16.9
16.9
14.6
13.0
11.2
AMPS
PHASE
'T' MODELS
WELLS/BLOOMFIELD * VERDI, NV
PANEL
CONTROL
MASTER
FRONT PANEL CUTOUT
TOP CUTOUT
SCREWDRIVER
COUNTERTOP
WELLSLOK
GASKET
WARMER FLANGE
FRONT OF THE FIXTURE.
MANIFOLD ARE LOCATED TO THE
THE CONTROL PANEL AND DRAIN
MOUNT APPLIANCE SO THAT BOTH
IMPORTANT:
3. Mount Control Box to apron cutout as shown in drawing.
required to secure flange tightly to countertop.
Wellslok frame and twist "ears" outward (clockwise) as
2. From underneath, insert screwdriver into "slots" in
flange.
to underside of gray gasket material supplied on mounting
to countertop, apply a bead of silicone adhesive/sealant
RECOMMENDATION: Before final seating of modular section
modular section into countertop cutout and position.
counter top cutout, then through apron cutout. Lower
1. Tilt and pass Control Panel and electrical box through
Master Control Panel when making installation.
IMPORTANT - DO NOT disconnect "lead wires" from the
TO INSTALL:
4. Unit shall be accessible for servicing from the bottom.
3. Cut out holes.
apron using the control box as a template.
2. Layout and fabricate control panel holes in counter
apron.
1. Layout "cutout" dimensions on countertop and front
TO FABRICATE:
the unit to avoid contact with elevated temperatures.
recommended that a baffle be placed 8 1/2 inches below
3. If storage is to be used underneath the unit, it is
2. Unit shall be accessible for servicing from the bottom.
6 3/4 inches to a surface below the unit.
6 inches to front wall, 1 inch to back and side walls, and
Wooden and Metal Installation: DO NOT install closer than
1. Required Installation Clearances:
OUTLINED BELOW UPON INSTALLATION:
INSTALLER MUST MEET CONDITIONS OF ACCEPTABILITY
FOR DM AND TDM MODELS ONLY.
MANIFOLD WITH 1" INTERNAL NPT VALVE IS SUPPLIED
ARE FIELD CONVERTIBLE TO SINGLE PHASE. THE DRAIN
NOTE: MOD-500 UNITS ARE SHIPPED THREE PHASE AND
CUTOUT DETAILS
INSTALLATION INSTRUCTIONS
37099-5 REV (-)
INSTALLATION INSTRUCTIONS
BUILT-IN MODULAR WARMERS
MOD 500 SERIES (T, TD, TDM)
(25)
(25)
(171)
(152)
MINIMUM CLEARANCE REQUIRED FROM
BACK
SIDE
BOTTOM
FRONT
1
1
6 3/4
6
ELECTRICAL
CLEARANCES
PRODUCT DIMENSIONS
'D' MODELS ONLY
INTERNAL N.P.T.
1/2 INCH
'T' MODELS
8 AWB Cu
8 AWB Cu
8 AWB Cu
8 AWB Cu
75°C
75°C
75°C
75°C
RATING
TEMP.
3 PHASE
1 PHASE
ALL MODELS WITH A "D" OR "DM" SUFFIX HAVE THE SAME ELECTRICAL SPECIFICATIONS AS THE STANDARD MOD-500 OR MOD-500T MODELS.
INCHES
(MM)
