Blink Marine PKP2500SI Instructions Manual Download

Page: 5 / 38

5/38

PKP2500SI_CANopenUM_REV1.0

www.blinkmarine.com

NMT MESSAGES

The Network Management messages follow a master-slave structure. Through NMT services, CANopen
devices are initialized, started, reset or stopped.
NMT messages have CAN-ID always equal to 00h.

Start CANopen node (keypad activation message)

Identifier

00h

Byte 0

01h

Start CANopen node

Byte 1

XXh

Keypad CAN ID
00h: start all the keypads

15h: start the keypad with CAN ID = 15h.

Byte 2, 7

00h

Not used

Example:

Direction

Identifier

Format

Message

To Keypad

Std

01 15

Enter pre-operational

Identifier

00h

Byte 0

80h

Enter pre-operational

Byte 1

XXh

Keypad CAN ID
00h: enter all the keypads

15h: enter the keypad with CAN ID = 15h.

Byte 2, 7

00h

Not used

Example:

Direction

Identifier

Format

Message

To Keypad

Std

80 15

Reset CANopen node

Identifier

00h

Byte 0

81h

Reset CANopen node

Byte 1

XXh

Keypad CAN ID
00h: reset all the keypads

15h: reset the keypad with CAN ID = 15h.

Byte 2, 7

00h

Not used

Example:

Direction

Identifier

Format

Message

To Keypad

Std

81 15

Summary of Contents for PKP2500SI







































Search results

Summary of Contents for PKP2500SI

Reviews:

Related manuals for PKP2500SI

Brands by name

Popular brands

Blink Marine PKP2500SI, Instructions Manual

Search results

Summary of Contents for PKP2500SI

Reviews:

Related manuals for PKP2500SI

Brands by name

Popular brands