FCC WARNING
The
equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These
are designed provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. and, if not installed and used in
accordance with instructions, may cause harmful interference with radio communications, However, there is no guarantee that radio interference will not occur in
installation. this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged
to consult the dealer or an experienced radio/TV technician for help.
You
cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
OWNER’S RECORD
The model and warranty numbers are located on the top of the unit. Record the
number in the space provided below. Refer to these numbers whenever you Call
upon your
Blaupunkt dealer regarding this product.
Warranty Number
FEATURES
Congratulations on your
purchase of this Blaupunkt FM/AM/Cassette Receiver. Its Optimum Reception Control (ORC IV) quartz FM and AM Tuner and high-quality,
player provide the ultimate in sound reproduction.
l
Tuner Features:
. Cassette Features:
l
Audio Features:
l
General Features:
ORC IV Tuner
Autoreverse Cassette Mechanism
36 Watt Max. Integrated
Detachable Faceplate for
12 FM/6 AM Presets
True Fast-Forward/Rewind
Amplifier
Switchable Clock/Function LCD Display
Travelstore FM/AM
Hard
Tape Head
Volume/Balance/Fader Controls
Quick-Connect Wire Harness
Automatic and Manual Tuning
Adjustable Turn-On Volume-Level
153.5 mm (7 2 6 in.)
Your unit’s detachable front faceplate makes the unit useless to would-be thieves.
Separate Bass and Treble Controls
DIN Chassis
Snap-In DIN Sleeve Mounting Hardware
PRECAUTIONS
.
your vehicle was parked in direct sunlight resulting in a considerable rise in temperature inside the vehicle,
the Unit
off before operating your unit.
. If no power connection is supplied to the unit, check the connections first, If everything is in order, check the fuse.
l
If no sound comes from the speakers of a two-speaker system, set the fader control to the center position.
l
You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty.
. If you have any questions or problems concerning your unit that are not covered in this manual, please contact your Blaupunkt dealer.
DETACHABLE FACE
Detaching Attaching the Face: The face of this unit can be detached and taken with you to prevent
from
stolen
Detaching the Face: Before detaching the face, be sure to press the PWR Button first. Then press the
REL (Release) Button and detach the face by gently pulling it off as Illustrated.
Note: Do not pull it straight out from the chassis. Be sure not to drop the face when detaching it
the chassis.
Attaching the Face: Apply the right hand side of the face to the chassis by sliding (part B) of the face to (part A) at the front of the chassis. Gently push the left side of the
against the front of the chassis until it snaps into place.
Note: Make sure that the face is inserted right side up. Do not press against the display window. Do not press hard against the face when attaching it to the chassis, it may be
attached with gentle pressure. Do not expose the face to direct sunlight, heat sources such as hot air ducts or leave it in a humid place. Never leave it on the dash board of a vehicle
parked in direct sunlight, where there may be a considerable
in temperature inside the vehicle.
Faceplate For Retail Display: The faceplate can be affixed to the units chassis, which is desirable for a retail display, for example. This should only be done in situations
where the unit can be accessed from behind the mounting surface. Once the faceplate is affixed, the release keys cannot be used to remove the chassis. To affix faceplate, obtain
the small bolt (M2.6 10) from hardware pack and drive it into the upper hole at the front of the left side of the chassis using a Phillips screwdriver. The bolt will self-thread the hole.
(See above*)