Wireless Outdoor Bell Box (BX-S1)
P
P
a
a
r
r
t
t
s
s
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
1. Mounting Holes x 4
2. Tamper Switch
The tamper switch protects the device from being opened or from
being removed from mounting surface.
3. Function Switch Block
Contains 7 DIP Switches to enable the learning mode and to set
the alarm period of siren and strobe light.
4. Power Switch
To enable/disable the power supply
5. Securing Screw
6. LEDs
P
P
a
a
c
c
k
k
a
a
g
g
e
e
C
C
o
o
n
n
t
t
e
e
n
n
t
t
1 x Outdoor Bell Box
4 x large wall plugs and screws
4 x 1.5V D alkaline batteries
D
D
i
i
p
p
S
S
w
w
i
i
t
t
c
c
h
h
1. Open the front cover and locate the Function Switch Block.
2. Use a sharp object to set Dip SW3 & SW4 on the function
switch block to your desired alarm length.
3. Enter learning mode for your control panel.
4. Slide the Power Switch to ON position to power on the
Bellbox.
5. Slide Dip SW1 to the ON position. The Bell Box LED 1 & 3 will
flash once with a short beep. The BX-S1 is now in learning
mode. After 3 seconds, the Bell Box will send out a learning
code, the LED 1 & 3 will flash once to confirm.
6. If the Control Panel receives the learning signal, please refer
to the Control Panel manual to complete the learning process.
When learning is complete, the Control Panel will send signal
to the Bell Box to confirm. The Bell Box will sound a short
beep and LED 1 & 3 will flash once to indicate learning is
successful.
If the Control Panel fails receive a learning code, slide Dip
SW1 back to OFF, and then ON position again to enter
learning mode again.
7. If the Bell Box does not respond, please remove the Bell Box
from the control panel and repeat steps 3-6 again.
8. Slide Dip SW1 to the OFF position to leave learning mode. If
you do not slide Dip SW1 back to OFF position, the Bell Box
will automatically leave the learning mode in one hour.
The Outdoor Bell Box has 4 mounting holes on the back cover for
wall mounting.
Before Installation, refer to your Control Panel manual to
temporarily disable the Siren Tamper function to avoid
accidental alarm trigger.
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
SW1
Siren Learning
OFF
Normal operation
ON
Learn-in mode
SW2
Strobe Activation
OFF
only during siren alarm period
ON
until alarm is disarmed
SW3
SW4
Siren Duration
OFF
OFF
3 min.
ON
OFF
5 min.
OFF
ON
10 min.
ON
ON
1 second (test)
SW5
Reserved
SW6
Memory Reset
OFF
Normal
ON
Clear Memory
SW7
Supervision
OFF
Supervision function disable
ON
Supervision function enable
For further detail please see
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
a
a
n
n
d
d
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
.
.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Mounting Holes
x 4
