Blackmagicdesign ATEM Camera Converter Installation And Operation Manual Download

Page: 56 / 136

Using the ATEM 2 M/E Broadcast Panel

DSK CUT

The DSK CUT button is used to cut the DSK on or off air and indicates whether the DSK is currently on or off
air. The button is illuminated if the DSK is currently on air.

DSK AUTO

The DSK AUTO button will mix the DSK on or off air at the rate specified in the DSK rate window.

Fade to Black

FTB

The FTB button will fade the program output to black at the rate specified in the FTB rate window. Once the
program output has been faded to black, the FTB button will remain illuminated red until it is pressed again,
fading the program output up from black at the same rate. A fade to black cannot be previewed.

System Status

The status lights provide feedback on the power supplies connected to the broadcast panel and switchers.
Not all ATEM switcher models have redundant power supplies so sometimes you will only see a single light
illuminated for the power status of the switcher.

However if your switcher model has redundant power and you have connected two power supplies to
the switcher and the control panel, then all the lights should be on. In this situation where you are using
redundant power supplies, any light that turns off could indicate a power supply is faulty, and this should
be checked.

When the 2 M/E panel is used to control two ATEM switchers, the switcher status lights indicate whether
the two switchers are powered on. In this context, the "Main" switcher status light refers to the lower M/E 1
control block, and "Backup" refers to the upper M/E 2 control block.

System Control

The twelve menu buttons, the display window, the four knobs and the four soft buttons under the knobs
together are called the system control. The 4 line display is used to identify the operation of the soft buttons
and knobs. The two system control blocks provide separate M/E 1 and M/E 2 controls.

The system control is context sensitive and allows you to adjust parameters for the current operation. For
example if you enable KEY 1 in your next transition, the system control allows you to adjust the parameters
of KEY 1. The system control is also used for configuring other parts of the switcher.

Power Status and System Control

Camera

Media

Player

Media

Player

Color

Bars

Media

Player

1 Key

Media

Player

2 Key

Color

Black

CLR

CAM

SHIFT

KEY 1

CUT

KEY 2

CUT

STNG

CUT

DVE

CUT

AUX 1

AUX 7

AUX 2

AUX 8

AUX 3

AUX 9

AUX 4

AUX 10

AUX 5

AUX 11

AUX 6

AUX 12

BORD

DIP

KEY 3

CUT

KEY 4

CUT

SHIFT

DEST

KEY 1

CUT

BORD

DIP

STNG

CUT

DVE

CUT

DSK 2

CUT

SSRC

CUT

BOX 1

DSK 1

CUT

KEY 2

CUT

KEY 3

CUT

KEY 4

CUT

BOX 3

BOX 2

BOX 4

SHIFT

DEST

TIE

DSK 1

TIE

DSK 2

CUT

DSK 1

CUT

DSK 2

AUTO

DSK 1

AUTO

DSK 2

WIPE

STNG

DVE

MIX

DIP

BKGD

KEY 1

KEY 2

KEY 3

KEY 4

WIPE

STNG

DVE

MIX

DIP

BKGD

KEY 1

KEY 2

KEY 3

KEY 4

BOX 2

BOX 4

PATT

M/E 2

KEY

M/E 2

BOX 2

BOX 4

PATT

M/E 1

KEY

M/E 1

AUTO

CUT

FTB

PREV

TRANS

AUTO

CUT

PREV

TRANS

AUX

TRANS

DSK

KEYS

EFFECTS

KEYS

MEDIA

PLAYER

COLOR

PANEL

SETUP

TRANS

DSK

KEYS

EFFECTS

KEYS

MEDIA

PLAYER

PANEL

SETUP

COLOR

Camera

Media

Player

Media

Player

Color

Bars

Media

Player

1 Key

Media

Player

2 Key

Color

Black

Camera

Media

Player

Media

Player

Color

Bars

Media

Player

1 Key

Media

Player

2 Key

Color

Black

CLR

CAM

SHIFT

KEY 1

CUT

KEY 2

CUT

STNG

CUT

DVE

CUT

AUX 1

AUX 7

AUX 2

AUX 8

AUX 3

AUX 9

AUX 4

AUX 10

AUX 5

AUX 11

AUX 6

AUX 12

BORD

DIP

KEY 3

CUT

KEY 4

CUT

SHIFT

DEST

KEY 1

CUT

BORD

DIP

STNG

CUT

DVE

CUT

DSK 2

CUT

SSRC

CUT

BOX 1

DSK 1

CUT

KEY 2

CUT

KEY 3

CUT

KEY 4

CUT

BOX 3

BOX 2

BOX 4

SHIFT

DEST

TIE

DSK 1

TIE

DSK 2

CUT

DSK 1

CUT

DSK 2

AUTO

DSK 1

AUTO

DSK 2

WIPE

STNG

DVE

MIX

DIP

BKGD

KEY 1

KEY 2

KEY 3

KEY 4

WIPE

STNG

DVE

MIX

DIP

BKGD

KEY 1

KEY 2

KEY 3

KEY 4

BOX 2

BOX 4

PATT

M/E 2

KEY

M/E 2

BOX 2

BOX 4

PATT

M/E 1

KEY

M/E 1

AUTO

CUT

FTB

PREV

TRANS

AUTO

CUT

PREV

TRANS

AUX

TRANS

DSK

KEYS

EFFECTS

KEYS

MEDIA

PLAYER

COLOR

PANEL

SETUP

TRANS

DSK

KEYS

EFFECTS

KEYS

MEDIA

PLAYER

PANEL

SETUP

COLOR

Camera

Media

Player

Media

Player

Color

Bars

Media

Player

1 Key

Media

Player

2 Key

Color

Black

Camera

Media

Player

Media

Player

Color

Bars

Media

Player

1 Key

Media

Player

2 Key

Color

Black

CLR

CAM

SHIFT

KEY 1

CUT

KEY 2

CUT

STNG

CUT

DVE

CUT

AUX 1

AUX 7

AUX 2

AUX 8

AUX 3

AUX 9

AUX 4

AUX 10

AUX 5

AUX 11

AUX 6

AUX 12

BORD

DIP

KEY 3

CUT

KEY 4

CUT

SHIFT

DEST

KEY 1

CUT

BORD

DIP

STNG

CUT

DVE

CUT

DSK 2

CUT

SSRC

CUT

BOX 1

DSK 1

CUT

KEY 2

CUT

KEY 3

CUT

KEY 4

CUT

BOX 3

BOX 2

BOX 4

SHIFT

DEST

TIE

DSK 1

TIE

DSK 2

CUT

DSK 1

CUT

DSK 2

AUTO

DSK 1

AUTO

DSK 2

WIPE

STNG

DVE

MIX

DIP

BKGD

KEY 1

KEY 2

KEY 3

KEY 4

WIPE

STNG

DVE

MIX

DIP

BKGD

KEY 1

KEY 2

KEY 3

KEY 4

BOX 2

BOX 4

PATT

M/E 2

KEY

M/E 2

BOX 2

BOX 4

PATT

M/E 1

KEY

M/E 1

AUTO

CUT

FTB

PREV

TRANS

AUTO

CUT

PREV

TRANS

AUX

TRANS

DSK

KEYS

EFFECTS

KEYS

MEDIA

PLAYER

COLOR

PANEL

SETUP

TRANS

DSK

KEYS

EFFECTS

KEYS

MEDIA

PLAYER

PANEL

SETUP

COLOR

Camera

Media

Player

Media

Player

Color

Bars

Media

Player

1 Key

Media

Player

2 Key

Color

Black

Downstream Keyers and Fade to Black

Camera

Media

Player

Media

Player

Color

Bars

Media

Player

1 Key

Media

Player

2 Key

Color

Black

CLR

CAM

SHIFT

KEY 1

CUT

KEY 2

CUT

STNG

CUT

DVE

CUT

AUX 1

AUX 7

AUX 2

AUX 8

AUX 3

AUX 9

AUX 4

AUX 10

AUX 5

AUX 11

AUX 6

AUX 12

BORD

DIP

KEY 3

CUT

KEY 4

CUT

SHIFT

DEST

KEY 1

CUT

BORD

DIP

STNG

CUT

DVE

CUT

DSK 2

CUT

SSRC

CUT

BOX 1

DSK 1

CUT

KEY 2

CUT

KEY 3

CUT

KEY 4

CUT

BOX 3

BOX 2

BOX 4

SHIFT

DEST

TIE

DSK 1

TIE

DSK 2

CUT

DSK 1

CUT

DSK 2

AUTO

DSK 1

AUTO

DSK 2

WIPE

STNG

DVE

MIX

DIP

BKGD

KEY 1

KEY 2

KEY 3

KEY 4

WIPE

STNG

DVE

MIX

DIP

BKGD

KEY 1

KEY 2

KEY 3

KEY 4

BOX 2

BOX 4

PATT

M/E 2

KEY

M/E 2

BOX 2

BOX 4

PATT

M/E 1

KEY

M/E 1

AUTO

CUT

FTB

PREV

TRANS

AUTO

CUT

PREV

TRANS

AUX

TRANS

DSK

KEYS

EFFECTS

KEYS

MEDIA

PLAYER

COLOR

PANEL

SETUP

TRANS

DSK

KEYS

EFFECTS

KEYS

MEDIA

PLAYER

PANEL

SETUP

COLOR

Camera

Media

Player

Media

Player

Color

Bars

Media

Player

1 Key

Media

Player

2 Key

Color

Black

Camera

Media

Player

Media

Player

Color

Bars

Media

Player

1 Key

Media

Player

2 Key

Color

Black

CLR

CAM

SHIFT

KEY 1

CUT

KEY 2

CUT

STNG

CUT

DVE

CUT

AUX 1

AUX 7

AUX 2

AUX 8

AUX 3

AUX 9

AUX 4

AUX 10

AUX 5

AUX 11

AUX 6

AUX 12

BORD

DIP

KEY 3

CUT

KEY 4

CUT

SHIFT

DEST

KEY 1

CUT

BORD

DIP

STNG

CUT

DVE

CUT

DSK 2

CUT

SSRC

CUT

BOX 1

DSK 1

CUT

KEY 2

CUT

KEY 3

CUT

KEY 4

CUT

BOX 3

BOX 2

BOX 4

SHIFT

DEST

TIE

DSK 1

TIE

DSK 2

CUT

DSK 1

CUT

DSK 2

AUTO

DSK 1

AUTO

DSK 2

WIPE

STNG

DVE

MIX

DIP

BKGD

KEY 1

KEY 2

KEY 3

KEY 4

WIPE

STNG

DVE

MIX

DIP

BKGD

KEY 1

KEY 2

KEY 3

KEY 4

BOX 2

BOX 4

PATT

M/E 2

KEY

M/E 2

BOX 2

BOX 4

PATT

M/E 1

KEY

M/E 1

AUTO

CUT

FTB

PREV

TRANS

AUTO

CUT

PREV

TRANS

AUX

TRANS

DSK

KEYS

EFFECTS

KEYS

MEDIA

PLAYER

COLOR

PANEL

SETUP

TRANS

DSK

KEYS

EFFECTS

KEYS

MEDIA

PLAYER

PANEL

SETUP

COLOR

Camera

Media

Player

Media

Player

Color

Bars

Media

Player

1 Key

Media

Player

2 Key

Color

Black

Summary of Contents for ATEM Camera Converter









































































































































Search results

Summary of Contents for ATEM Camera Converter

Reviews:

Related manuals for ATEM Camera Converter

Brands by name

Popular brands

Blackmagicdesign ATEM Camera Converter, Installation And Operation Manual

Search results

Summary of Contents for ATEM Camera Converter

Reviews:

Related manuals for ATEM Camera Converter

Brands by name

Popular brands