RACEDAY
PORTABLE
Trainer
Part# 7079860
Customer Service: 1-800-456-2355
Blackburndesign.com
Printed in Taiwan
TELESCOPING LEG
STEP 1: Prior to installing the bicycle onto the trainer, decide if the front
axle is a 9mm skewer, a 12mm thru axle or 15 mm thru axle.
STEP 2: You will also need to check if the front hub width is 100mm or
110mm Boost. (Figure 2)
STEP 3: Loosen the connector dial by turning counter-clockwise and
lengthen the telescoping connector to fit the wheelbase of your bicycle.
Tighten the connector dial once you have the correct extended length.
STEP 4: Pull the leg out from the base until you hear an audible “snap.”
The leg will be locked into place.
STEP 5: Adjust the length of the legs so the bike is as level as possible or
comfortable as possible when mounted on the trainer by pushing the
spring button and moving the telescoping legs up or down.
STEP 6: Place rear wheel of bicycle onto rollers. If your front axle is:
A. 9mm skewer (Figure 3A), remove the front wheel and skewer.
Position the front fork of the bicycle onto the fork mount of the trainer.
Attach the fork of the bicycle to the fork mount of the trainer using the
included quick release skewer. Follow your bicycle/wheel manufactur-
er recommendations for removing and installing quick releases or have
a qualified bicycle shop replace it for you.
B. 12mm thru axle – (Figure 3B). Remove quick release skewer from
trainer mount. Remove the 100/110mm endcap adapters. Remove the
9mm spacer in the mount and replace with the 12mm yellow spacer
(included separately in a bag). Install the 12mm yellow spacer into mount
and then cap off the ends with the 100/110 adapter. Remove the front
wheel of the bicycle. Position the front fork of the bicycle onto the fork
mount of the trainer. Attach fork using your 12mm thru axle and tighten.
C. 15mm thru axle - (Figure 3C). Remove quick release skewer from
trainer mount. Remove the 100/110mm endcap adapters from mount.
Remove the 9mm spacer in the mount. Press the 100/110mm endcap
adapters onto each side of the mount. Remove the front wheel of the
bicycle. Position the front fork of the bicycle onto the fork mount of the
trainer. Attach fork using your 15mm thru axle and tighten.
STEP 7: Carefully get on the bicycle and start pedaling slowly. Do not
make any sudden moves until you are sure the bicycle is securely
mounted onto the trainer.
STEP 8: When finished using trainer, fold the trainer to its smallest
position by doing the following:
A. Shorten telescoping legs by pushing on the spring button and
pushing the leg up close to the base of the trainer. Next, fold in the leg
struts by pushing on the leg strut spring button and pushing the legs in.
B. Next, shorten the connector by turning the connector dial
counter clockwise.
C. Fold the rollers up to the base for smallest footprint. (Figure 4)
Optional: Use rubber straps installed on trainer to secure.
FORK MOUNT
LEG STRUTS
TELESCOPING LEG
SPRING BUTTONS
LEG STRUT
SPRING BUTTONS
CONNECTOR DIAL
B
TELESCOPING CONNECTOR
FLUID ROLLERS
HUB WIDTH: Your trainer has been pre-configured to accommodate a 100mm
front hub width vs 110 mm hub. Most road and mountain bikes are 100mm.
“Boost 110” hub configuration requires 110mm spacing. Flip adapter to
change from 100 mm hub width to 110 mm.
THE QUICK CHANGE SPACERS ACCOMODATE THE FOLLOWING AXLES:
A. 9 mm quick release: 9 mm quick release provided
B. 12 mm thru axle: 12 mm thru axle use on the bike
C. 15 mm thru axle: Thru axle use on the bike (no spacer)
NOTE: Your trainer has been pre-configured to accommodate a 9mm
diameter front hub.
FIGURE 3: AXLE ACCOMODATION
FIGURE 2: HUB WIDTH
LEG
100MM
110MM
ADAPTER
A.
B.
C.
FIGURE 1: ADJUSTING LENGTH
Visit us at blackburndesign.com for product updates.
Visitez le site Internet blackburndesign.com pour obtenir les mises à jour sur les produits.
Informationen über Produktverbesserungen finden Sie unter www.blackburndesign.com
WARNING:
FAILURE TO FOLLOW TRAINER SETUP AND BICYCLE
INSTALLATION INSTRUCTIONS PROPERLY MAY RESULT IN POTENTIAL
DANGER TO THE USER. USE TRAINER AWAY FROM CHILDREN AND PETS AS
MOVING PARTS CAN BE DANGEROUS TO THEM DURING NORMAL USE.
AVERTISSEMENT :
SI LES INSTRUCTIONS D'INSTALLATION ET L'ENTRAÎNEUR
ET DU VÉLO NE SONT PAS APPLIQUÉES CORRECTEMENT, CELA PEUT CRÉER
UN DANGER POTENTIEL POUR L'UTILISATEUR. GARDEZ LES ENFANTS ET
LES ANIMAUX DE COMPAGNIE À DISTANCE DE L'ENTRAÎNEUR CAR DES
PIÈCES MOBILES PEUVENT ÊTRE DANGEREUSES POUR EUX PENDANT LE
FONCTIONNEMENT NORMAL.
WARNUNG:
BEI NICHTBEACHTUNG DER INSTALLATIONSANWEISUNGEN UND
AUFSTELLUNG DES TRAINERS UND FAHRRADS KANN GGF. FÜR DEN BENUTZER
GEFÄHRLICH SEIN. BENUTZEN SIE DEN TRAINER AUßER REICHWEITE VON
KINDERN UND HAUSTIEREN, DA DIE BEWEGLICHEN TEILE GEFÄHRLICH FÜR
SIE SEIN KÖNNEN.
