background image

24

L-39 ALBATROS  

Item code: BH141

 .                                          

 

Instruction Manual

We wish you many  safe and enjoy-

able flights with your 

L-39 ALBATROS.

Ailerons :   10 mm up     10 mm down

Flap      :     30 mm

Elevator :  12 mm up   12 mm down

Rudder :   15 mm right   15 mm left





1) We highly recommend setting up a

plane using the control throws listed.





2) The control throws should be meas-

ured at the widest point of each control sur-
face.





3) Check to be sure the control surfaces

move in the correct directions.

CONTROL THROWS.





1) Completely charge your transmitter and

receiver batteries  before your first day of fly-
ing.





2) Check every bolt and every glue joint in

your plane to ensure that everything is tight
and well bonded.





3)  Double check the balance of the

airplane.





4) Check the control surface.





5) Check the receiver antenna . It should

be fully extended and not coiled up inside the
fuselage.





6) Properly balance the propeller.

PRE-FLIGHT CHECK.

Flap control

Aileron control

Elevator control

Rudder control

  10 mm

   10mm

    12 mm

   12 mm

   30 mm

  15  mm

    15mm

Summary of Contents for L-39 Albatros BH 141

























Reviews: