6 • ENGLISH
f
Do not use to pick up flammable or combustible liquids
such as gasoline or use in areas where they may be present.
f
To avoid spontaneous combustion, empty tank after each use.
f
Do not pick up anything that is burning or smoking, such
as cigarettes, matches, or hot ashes.
f
Do not use without dust bag and/or filter in place.
f
To reduce the risk of the electric shock. Make sure the
plug is dry and do not operate with wet hands.
f
Do not run vacuum unattended.
f
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or a similarly qualified
person in order to avoid a hazard.
f
The appliance is not be used by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction.
f
Childre being supervised not play with the appliance.
CARTON CONTENTS LIST - FIG. A
PART
DESCRIPTION
QTY
1
Vaccum assembly
1
2
Flexible hose
1
3
Sofa brush
1
4
Floor brush
1
5
Crevice nozzle
1
6
Extension tube
2
7
Wheel
4
8
Washable dust bag
1
9
User manual
1
10
HEPA filter
1
11
HEPA filter cover
1
12
Sponge filter
1
DRUM ASSEMBLY
Warning! If any part is missing or damaged, please do not
assemble until you have all the parts.
Invert drum to install wheel
Insert the four wheels (7) into the socket of wheel base.
Be sure that wheels spin freely (Fig. B)
ASSEMBLING THE UNIT
1. Put the HEPA filter (10) into float holder, then lid the HEPA
filter cover (11), fasten it clockwise. On the contrary,
remove the HEPA filter anticlockwise (Fig. C).
NOTE: When picking up small amounts of liquid the HEPA
filter can be left in place. When picking up large amounts
of liquid we recommend that the HEPA filter should be
removed. If the HEPA filter is not removed, it will become
saturated and misting may appear in the exhaust.
2. Fitting the dust bag. Put the dust bag board (8) into inlet
base. (Dust bag board should be aim at the slot of the inlet
base). Rotate the board clockwise 90º degrees to fasten
the dust bag according to arrow direction (LOCK side)
(Fig. D).
To remove the dust bag from the inlet base, just rotate the
dust bag board anticlockwise 90º degree (OPEN side),
then take out the dust bag.
NOTE: The dust bag use only for dry-vacuum.
3. Install the power head assembly into the drum assembly
as shown (Fig. E).
4. Rotate both latches down and press until you hear them
snap over the flanges on the drum (Fig. F).
5. Insert the flexile hose connector into the inlet base of the
vacuum cleaner (Fig. G).
OPERATION
Accessories use instructions
The vacuum cleaner is equipped with three nozzles for different
applications. Each individual nozzle can either be fitted onto the
connecting tube or directly onto the handle of the flexible hose.
1. Floor brush
This is suitable for cleaning wide areas. The floor brush is
fitted with a practical 360º tie-in, this ensures that you can
reach easily into any corner (Fig. H).
2. Crevice nozzle
This nozzle is suitable for sucking and cleaning the corners or
niches that cannot be reached with the floor brush. Besides, it
can be used as blowing tool (Fig. I).
3. Sofa brush
You can use this to clean the dust from books or sensitive
objects such as picture frames etc. This nozzle is suitable
for the careful cleaning of upholstered furniture, mattresses,
cushions, curtains etc. (Fig. J)
ATTENTION!
1. Make sure all the assembly is according to the instructions.
Connect the hose to the unit, then install the specific
accessories for the intended cleaning purpose. Insert the
plug into the socket. Press the ON/OFF switch button, start
the using. After using, press the ON/OFF switch button to
stop. Unplug the cord from the socket. (Fig. K)
WET VACUUMING
Caution! Always remove the dust bag when you commencing
wet vacuuming.
