Black+Decker Dustbuster DVA320BF, Manual

Page: 6 / 12

6
ENGLISH
Labels on appliance
The following symbols appear on this appliance along with the
date code.
+
Read all of this manual carefully before
using the appliance
S010Q 14
Only use with charger S010Q 14
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Dust chamber release button
3. Dust chamber
4. Flip up brush
5. Wall bracket
6. Charger base
7. Hanging attatchment
8. Filter
9. Floor head
10. Extension tubes
11. Adaptor
Use
Switching on and off (Fig. A)
u
Push the On/off power switch (1) to the forward position to
turn on the unit.
u
Returning the On/off power (1) switch will turn the unit off.
Flip down brush (Fig. B)
u
Flip the brush attachment (4) into position as shown in
figure B.
Using the pull out crevice tool (Fig. C)
u
Extend the crevice tool (12) as shown in figure C, until it
clicks in place.
Note: The flip down brush (4) can only be utilised when the
crevice tool is in the retracted position.
Fitting the wall bracket (Fig. D)
u
Fit the wall bracket (5) to a suitable wall (preferably near a
power outlet) using the screws provided.
u
The unit can then be stored, when not in use, or during the
charging procedure, utilising the hanging attachment (7).
Charging (Fig. F)
u
Place the appliance onto the charging base (6).
u
Place the charging plug into a power outlet and switch on
as shown in figure F. The charger LED will light.
Cleaning the filters (Fig. G, H, I, J, K,L)
u
Press the dust chamber release button (2) as shown in
figure G.
u
Seperate the dust chamber (3) from the motor unit as
shown in figure H.
u
You can use the easy empty feature as shown in figure I.
u
Lift the filter (8) out of the dust chamber (3) using the tab
(14) provided.
u
Empty the dust bowl (3) by lightly shaking over a suitable
container as shown in figure K.
u
Rinse out the dust-bowl with warm soapy water.
u
Wash the filters with warm soapy water as shown in figure
L.
u
Allow the filters to dry naturally, using heat may cause the
filters to distort.
u
Refit the filter (8) into dust chamber (3). Make sure the
filter tabs (13) face forward. Never place the filters into
the dust chamber backwards.
u
Replace the dust chamber onto the motor unit. Make sure
the release button (2) clicks into place.
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water
Maintenance
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
u
Run the battery down completely if it is integral and then
switch off.
u
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u
Regularly clean the ventilation slots in your appliance/
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Replacing the filters
The filters should be replaced every 6 to 9 months and when -
ever worn or damaged. Replacement filters are available from
your BLACK+DECKER dealer.
u
Remove the old filters as described above.
u
Fit the new filters as described above.
Protecting the environment