Black Box MT136A User Manual Download Page 75 | Manualshive

Page: 75 / 116

Black Box MT136A User Manual Download Page 75

74

CSU/DSU MS DBU

12.1.3 E

XITING A

T

EST

During a test, press Quick to access the Exit Test/Display Status menu or press
Cancel to return to the Main menu. The Exit Test/Display Status menu provides
the following options, which are available only after a test has been initiated
(see Figure 12-4):

Exit Test

Exits the current test and returns to the Main menu.

Display Status

Reenters test display.

Figure 12-4. Complete Test Menu.

12.2 Troubleshooting

This section is intended to provide a quick and easy means of diagnosing suspected
problems associated with local or remotely attached Black Box DSU/CSUs.

12.2.1 M

ESSAGES FROM THE

DSU/CSU

Messages on the LCD display and LEDs give information concerning the status of
the unit and the local loop. If the Alarm LED is On, one or more of the messages
shown in Table 12-1 are displayed on the LCD.

2=TEST

1=LOCAL UNIT

2=REMOTE UNIT

3=DBU CONNECTION

1=DIAL STORED #

2=ENTER DIAL #

3=REDIAL LAST #

1=2047 PATTERN

2=511 PATTERN

3=STRESS PTRN #1

4=STRESS PTRN #2

5=STRESS PTRN #3

6=STRESS PTRN #4

1=2047 PATTERN

2=511 PATTERN

3=STRESS PTRN #1

4=STRESS PTRN #2

5=STRESS PTRN #3

6=STRESS PTRN #4

7=DATA FROM DTE

1=DTE & LOOP(LL)

2=LOOP ONLY(RT)

3=DTE ONLY

4=DTE WITH TP

5=TEST PATTERN

6=SELF TEST

ENTER TEST UNIT

ADDRESS:0

«
...
73
74
75
76
77
...
»

Summary of Contents for MT136A





















































































































Reviews:

No comments