Black Box MT136A User Manual Download Page 65 | Manualshive

Page: 65 / 116

Black Box MT136A User Manual Download Page 65

64

CSU/DSU MS DBU

10.3 IP Options

NOTE

When configuring the CSU/DSU MS DBU with the front panel, use the “*”
key to enter a decimal point.

10.3.1 U

NIT

IP A

DDRESS

Enter the CSU/DSU MS DBU IP address in dotted decimal notation.

10.3.2 S

UBNET

M

ASK

Enter the subnet number in dotted decimal notation. This address is available
from the network administrator.

10.3.3 G

ATEWAY

IP A

DDRESS

Enter the Gateway node IP address in dotted decimal notation. This address is
necessary only if the CSU/DSU MS DBU and network manager are connected
through a Gateway node. If an IP packet with an unknown IP address is received,
the CSU/DSU MS DBU sends it to the Gateway.

10.3.4 IP S

ECURITY

Enable/disable the IP security option. If enabled, the CSU/DSU MS DBU only
accepts management commands from the IP addresses (up to 5) entered into
the IP Filter Address field.

10.3.5 IP F

ILTER

A

DDRESS

Enter the IP addresses of the management stations from which the CSU/DSU MS
DBU should accept management commands. This filter must be enabled though
the IP Security field.

«
...
63
64
65
66
67
...
»

Summary of Contents for MT136A





















































































































Reviews:

No comments