manualshive.com logo in svg

Black Box MT136A, User Manual, Page: 60 / 116

Share
Download
Black Box MT136A User Manual Download Page 60

59

CHAPTER 9: Configuring Dial Options

Table 9-2 (continued). DBU Options AT Commands for All Models

Front Panel

AT Command

Description

1=Disabled

_H0

No DBU when RX signal absent

2=Enabled

_H1

DBU when RX signal absent

NO SEALING CURRENT

1=Disabled

_I0

No DBU when sealing current absent

2=Enabled

_I1

DBU when sealing current absent

WHEN ALL 1S/0S

1=Disabled

_P0

No DBU when all-1s/0s detected

2=Enabled

_P1

DBU when all-1s/0s condition exists

ANSWER ALWAYS

1=Disabled

none

Answer unit answers only under 

specified conditions.

2=Enabled

none

Answer unit answers any incoming 

call regardless of failed condition.

WEEKEND LOCKOUT

1=Disabled

none

Disables weekend lockout feature

2=Enabled

none

No backup occurs from midnight 

Friday to midnight Sunday

DAILY LOCKOUT

1=Disabled

none

Sets dial-backup lockout starting 

hour

2=Enabled

none

Sets dial backup lockout ending hour

LOCKOUT START

none

Sets hour to enable dial backup

LOCKOUT END

none

Sets hour to disable dial backup

Auto Restore

S31=x

Sets restore timer

Redial Counter

S57=x

Sets redial counter

Fail Timer

S58=x

Sets fail timer

Wait to Redial

S59=x

Sets time between redial attempts

9.3.2 DBU O

PTIONS FOR

S4W

Network Type

This option selects the company providing the switched digital service. When US
Sprint is selected, an automatic echo canceler suppressor tone is emitted by the
CSU/DSU MS DBU when dialing. Options include: AT&T/MCI/Other and US
Sprint.

Summary of Contents for MT136A





















































































































Reviews:

No comments