manualshive.com logo in svg

Black Box MT136A, User Manual, Page: 53 / 116

Share
Download
Black Box MT136A User Manual Download Page 53

52

CSU/DSU MS DBU

Table 8-1. Test Options AT Commands

Front Panel

AT Command

Description

Test Timeout

ENTER TIMEOUT

S18=x

Specify 0-255 second test timeout

RDL Enable/Disable

1=RDL IGNORED

&T5

RDL request from remote DSU ignored

2=RDL ACCEPTED

&T4

RDL request accepted

EIA LLB Enable/Disable

1=DISABLED

_A0

No response to local loopback

2=ENABLED

_A1

Responds to local loopback

EIA RLB Enable/Disable

1=DISABLED

_R0

No response to remote loopback

2=ENABLED

_R1

Responds to remote loopback

DBU Answer Test

1=DISABLED

none

Remote unit does not accept DBU 

tests from far end

2=ENABLED

none

Remote unit accepts DBU tests from 

far end

T

EST

T

IMEOUT

The Test Timeout option sets the length of time a CSU/DSU MS DBU remains in
a test mode before automatically returning to the data mode. Enter the timeout as
a two-digit decimal value. The factory-default setting is off (0).  

R

EMOTE

D

IGITAL

L

OOPBACK

(RDL)

The RDL option specifies whether the CSU/DSU MS DBU responds to an RDL
request from the far end of the circuit. The factory-default setting is RDL
Accepted.

EIA LLB

The EIA LLB (Electronics Industries Association local loopback) option specifies
whether the CSU/DSU MS DBU responds to the local loopback input from the
DTE. The factory-default setting is Disabled.

EIA RLB

The EIA RLB (remote loopback) option specifies whether the CSU/DSU MS DBU
responds to the RLB input from the DTE. The factory-default setting is Disabled.  

Summary of Contents for MT136A





















































































































Reviews:

No comments