manualshive.com logo in svg

Black Box MT136A, User Manual, Page: 33 / 116

Share
Download
Black Box MT136A User Manual Download Page 33

32

CSU/DSU MS DBU

M

INIMUM

C

ONFIGURATION

R

EQUIREMENTS FOR

SNMP/TELNET A

CCESS

The following options are the minimum configuration requirements for
establishing SNMP or TELNET access. Once these options are configured,
the remaining options may be configured using SNMP/TELNET. See the menu
tree in Figure 10-1 in Chapter 10 for the front-panel menu path to these options.

Interface

Select SLIP Control, PPP Control, or Ethernet LAN as the CSU/DSU MS DBU
interface type. The SNMP Ethernet Module must be installed to select Ethernet
LAN.

IP Address

Enter the CSU/DSU MS DBU IP address.

Subnet Mask

Enter the subnet number. This address is available from the network
administrator.

Gateway IP Address (if required)

Enter the Gateway node IP address. This address is necessary only if the CSU/DSU
MS DBU and the network manager are connected through a Gateway node. This
address is available from the network administrator.

S

PECIAL

F

EATURES OF THIS

A

PPLICATION

Customize the SNMP/TELNET application using the following CSU/DSU MS
DBU features:

• Designate SNMP hosts to receive SNMP traps from the CSU/DSU MS DBU

(one to five entries).

• Secure the CSU/DSU MS DBU by limiting SNMP network management

access. If enabled, the CSU/DSU MS DBU only responds to a user-configured
list of SNMP network managers (one to five entries).

Configure these options through the Management portion of the Configuration
menu. See Chapter 10 for more information.

Summary of Contents for MT136A





















































































































Reviews:

No comments