manualshive.com logo in svg

Black Box MT136A, User Manual, Page: 20 / 116

Share
Download
Black Box MT136A User Manual Download Page 20

19

CHAPTER 2: Installation

2. Installation

2.1 Unpack, Inspect, Power Up

I

NSPECTION

Carefully inspect the CSU/DSU MS DBU for any shipping damage. If damage
is suspected, file a claim immediately with the carrier and contact Black Box
Customer Service. Keep the original shipping container for use in shipping
the CSU/DSU MS DBU for repair or for verification of damage during shipment.

The following items are included with the CSU/DSU MS DBU:

• CSU/DSU MS DBU unit

• The user manual 

• An 8-position modular to 8-position modular cable

• An 8-position modular to 8-position modular cable and a modular to female

DB25 adapter for access to the Control/SLIP/PPP port

NOTE

The Black Box CSU/DSU MS DBU MIB is available from Black Box in the
support section of the Black Box Web page at www.blackbox.com.

The following items are included with the DBU Modules:

• DBU Module

• An 8-position modular to 8-position modular cable for the 4-wire SW56 and

1B+D ISDN dial-backup options. An 8-position modular to 4-position modular
cable for the V.34 backup option.

You must provide either a male EIA-232 (standard DB25) or a male V.35 interface
cable.

For SNMP management, you must provide access to the CSU/DSU MS DBU
through either a SLIP port, an async PPP port (requires a male DB25 connector),
or a 10BASE-T Ethernet port (requires that an SNMP Ethernet Module be installed

Summary of Contents for MT136A





















































































































Reviews:

No comments