manualshive.com logo in svg

Black Box MT136A, User Manual, Page: 109 / 116

Share
Download
Black Box MT136A User Manual Download Page 109

108

CSU/DSU MS DBU

Appendix D. Configuration Profiles

The CSU/DSU MS DBU contains four different user profiles (sets of configuration
options) stored in read-only memory; see Table D-1. The unit is shipped from the
factory with profile 1 loaded into the nonvolatile configuration memory. See
Section 11.1 for more information on entering the manual commands required
to load these profiles.

P

ROFILE

1

Profile 1 is configured for a 56-kbps, synchronous, point-to-point or dial-up
operation with a V.35 connector. Automatic DBU has been disabled for this
configuration profile.

P

ROFILE

2

Use profile 2 for a 56-kbps, asynchronous, point-to-point or dial-up operation,
with an EIA-232 connector. Automatic DBU has been disabled for this
configuration profile.

P

ROFILES

3 

AND

4

Profiles 3 and 4 are identical to profile 1 with the addition of dial-backup
capability. These profiles are used for enabling dial backup using two CSU/DSU
MS DBU. One must be set for Answer and the other for Originate. Use profile 3
to set the remote unit to Answer and profile 4 to set the host unit to Originate.

Table D-1. Configuration Profiles

Profile Numbers

(00) 1

(01) 2

(02) 3

(03) 4

Manual Command

Escape Character

43=2BH

43=2BH

43=2BH

43=2BH

CR Character

13=0DH

13=0DH

13=0DH

13=0DH

LF Character

10=0AH

10=0AH

10=0AH

10=0AH

BS Character

8

8

8

8

DBU Abort Call Timer

50=32H

50=32H

50=32H

50=32H

Escape Guard Timer

50=32H

50=32H

50=32H

50=32H

Command Echo

Enable

Enable

Enable

Enable

Result Code

Enable

Enable

Enable

Enable

Long or Short Code

Long

Long

Long

Long

Summary of Contents for MT136A





















































































































Reviews:

No comments