background image

27

APPENDIX: Transmission Distance Charts

Appendix. Transmission Distance

Charts

Table A-1. Transmission distance HDSL Line Driver, no crosstalk.

Line Rate DTE Rates

26 AWG (0.4 mm)

24 AWG (0.5 mm)

(kbps)

(kbps)

ft.

mi.

km

ft.

mi.

km

144

64, 128

20,700

3.9

6.3

24,500 4.6

7.5

272

192, 256

17,400

3.3

5.3

24,200 4.6

7.4

400

320, 384

15,100

2.9

4.6

22,600 4.3

6.9

528

448, 512

14,900

2.8

4.5

21,000 4

6.4

784

576, 640,

13,500

2.6

4.1

18,000 3.4

5.5

704, 768

1040

832, 896,

11,900

2.2

3.6

15,500 2.9

4.7

960, 1024

1168

1088, 1152

11,000

2.1

3.3

15,200 2.9

4.6

Table A-2. Transmission distance HDSL Line Driver, crosstalk (49 adjacent

CAP pairs).

Line Rate DTE Rates

26 AWG (0.4 mm)

24 AWG (0.5 mm)

(kbps)

(kbps)

ft.

mi.

km

ft.

mi.

km

144

64, 128

18,600

3.5

5.7

22,100 4.2

6.7

272

192, 256

15,700

3

4.8

21,800 4.1

6.6

400

320, 384

12,800

2.4

3.9

19,200 3.6

5.9

528

448, 512

13,000

2.5

4

18,300 3.5

5.6

784

576, 640,

12,200

2.3

3.7

16,200 3.1

4.9

704, 768

1040

832, 896,

10,500

2

3.2

13,600 2.6

4.1

960, 1024

1168

1088, 1152

9400

1.8

2.9

12,900 2.4

3.9

Summary of Contents for ME0006A-10BT






























Reviews: