background image

Chapter 3: Installation 

 

                     724-746-5500   |   blackbox.com

 

Page 17

3. INSTALLATION 

 

Before installing the equipment, it is necessary to take the following precautions: 

1.)  

If the equipment is mounted in an enclosed or multiple rack assembly, the 
steady-state long-term environmental temperature around the equipment must 
be less than or equal to 60

0

C. 

2.)  

If the equipment is mounted in an enclosed or multiple rack assembly, adequate 
airflow must be maintained for proper and safe operation. 

3.)  

If the equipment is mounted in an enclosed or multiple rack system, placement 
of the equipment must not overload or load unevenly the rack system. 

4.)  

If the equipment is mounted in an enclosed or multiple rack assembly, verify the 
equipment’s power requirements to prevent overloading of the building/s 
electrical circuits. 

5.)  

If the equipment is mounted in an enclosed or multiple rack assembly verify that 
the equipment has a reliable and uncompromised earthing path

.

 

 
This section describes installation of the LBH08x/LBH18x Switches, as well as 
connection of the various Ethernet media types.

 

 

3.1 Locating 

LBH08x/LBH18x Series Switches 

For vertical panel mounting and wall mounting, see Section 3.1.2 

For vertical DIN-Rail mounting, see Section 3.2 

For DC power input data, see Appendix B. 

 

 

  

The rugged metal case of the LBH08x/LBH18x will normally protect it from 

accidental damage in a lab or workplace setting.  Maintain an open view of the front 
to visually monitor the status LEDs.  Keep an open area around the unit so that 
cooling can occur from convection while the unit is in operation. The switch has no 
fans, so it is silent when in operation.  Internal electronics use the case as a heat 
sink, so the unit may normally be quite warm to the touch. 

 
3.1.1 

Table Top or Shelf Mounting 

 

The LBH08x/LBH18x Industrial switch can be easily mounted on a table-top 

or any suitable horizontal surface, and has four rubber feet to provide stability without 
scratching finished surfaces.  

 

3.1.2 

Mounting Dimensions with metal brackets 

 

Each LBH08x/LBH18x switch is supplied with metal mounting brackets and 

screws to mount the unit securely on a panel or wall. It is recommended to mount the 
switch vertically in the mounting position shown below, for proper cooling and long-life 
reliability. It is also advisable to mount the unit with space for air movement around 
the top and the sides, typically a minimum of 1 inch.

 

Summary of Contents for LBH081A

































Reviews: