Black Box AC1060A-R2 Manual Download Page 3

 

FEDERAL COMMUNICATIONS COMMISSION 

AND 

INDUSTRY CANADA 

RADIO FREQUENCY INTERFERENCE STATEMENTS 

 
 

This equipment generates, uses, and can radiate radio-frequency energy, and if 
not installed and used properly, that is, in strict accordance with the manufacturer’s 
instructions, may cause interference to radio communication. It has been tested 
and found to comply with the limits for a Class A computing device in accordance 
with the specifications in Subpart B of Part 15 of FCC rules, which are designed to 
provide reasonable protection against such interference when the equipment is 
operated in a commercial environment. Operation of this equipment in a 
residential area is likely to cause interference, in which case the user at his own 
expense will be required to take whatever measures may be necessary to correct 
the interference. 
 
Changes or modifications not expressly approved by the party responsible 
for compliance could void the user’s authority to operate the equipment. 

 
This digital apparatus does not exceed the Class A limits for radio noise emission 
from digital apparatus set out in the Radio Interference Regulation of Industry 
Canada. 
 
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les 
limites applicables aux appareils numériques de la classe A prescrites dans le  
 
Règlement sur le brouillage radioélectrique publié par Industrie Canada. 
 
 
 
 

EUROPEAN UNION DECLARATION OF CONFORMITY 

 
The manufacturer declares that this product meets the requirements of 
EU Directive 89/336/EEC.

 

FCC/IC RFI STATEMENTS, EU DECLARATION OF CONFORMITY 

 

FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY 

INTERFERENCE STATEMENTS 

 

This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, 
that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. 
It has been tested and found to comply with the limits for a Class A computing device in accordance with the 
specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection against 
such interference when the equipment is operated in a commercial environment. Operation of this equipment in 
a residential area is likely to cause interference, in which case the user at his own expense will be required to 
take whatever measures may be necessary to correct the interference. 
 
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s 
authority to operate the equipment. 

 
This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out 
in the Radio Interference Regulation of Industry Canada. 
 
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux 
appareils numériques de la classe A prescrites dans le  
 
Règlement sur le brouillage radioélectrique publié par Industrie Canada. 

 

 

     

EUROPEAN UNION DECLARATION OF CONFORMITY 

 

    The manufacturer declares that this product meets the requirements of  
    EU Directive 89/336/EEC. 

 

NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT 

INSTRUCCIONES DE SEGURIDAD 

 

1.

Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea 
operado. 

2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura. 
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas. 
4. Todas las instrucciones de operación y uso deben ser seguidas. 
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, 
sótano mojado o cerca de una alberca, etc.. 
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el 
fabricante. 
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante. 
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las 
instrucciones de operación. Todo otro servicio deberá ser referido a personal de servicio calificado. 
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del 
aparato eléctrico sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe 
colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilación. 
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de 
calor, estufas u otros aparatos (incluyendo amplificadores) que producen calor. 
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de 
operación, o como se indique en el aparato. 
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada. 
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por 
objetos colocados sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen 
del aparato. 
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante. 
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia. 
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de 
tiempo. 
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u 
orificios de ventilación. 
18. Servicio por personal calificado deberá ser provisto cuando: 
A: El cable de poder o el contacto ha sido dañado; u 
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o 
C: El aparato ha sido expuesto a la lluvia; o 
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o 
E: El aparato ha sido tirado o su cubierta ha sido dañada. 

Summary of Contents for AC1060A-R2





























Reviews: