9
E N G L I S H
Do not use the plug if the fuse cover is missing
or damaged.
Never use a light socket.
Using an extension cable
Always use an approved extension cable suitable
for the power input of this tool (see technical
data). Before use, inspect the extension cable for
signs of damage, wear and ageing. Replace the
extension cable if damaged or defective.
When using a cable reel, always unwind the cable
completely. Use of an extension cable not suitable
for the power input of the tool or which is
damaged or defective may result in a risk of fire
and electric shock.
CARTON CONTENTS
The carton contains:
1 Angle grinder
1 Side handle
1 Flange set
1 Two-pin spanner
1 Wrench (KG68/CD500)
1 Instruction manual
◆
Carefully unpack all parts.
◆
Please note that additional items may be
found in the carton, depending on the letter
suffix following the catalogue number of your
tool.
OVERVIEW (fig. A)
1. On/off switch
2. Side handle
3. Spindle lock (KG70/KG75)
4. Guard
5. Grinding or cutting disc
ASSEMBLY
Before attempting any of the following
operations, make sure that the tool is
switched off and unplugged.
Fitting and removing the guard
Fitting (fig. B)
◆
Place the tool on a table, with the spindle (6)
facing up.
◆
Hold the guard (4) over the tool as shown.
◆
Align the lug (7) with the slot (8).
◆
Press the guard down (A) and turn it
counterclockwise (B).
Removing (fig. C)
◆
While holding the tool, turn the guard (4)
clockwise.
◆
Use a screwdriver to press down the locking
pin (9).
◆
Release the guard and take it off the tool.
Never use the tool without the guard,
except when sanding.
Fitting the side handle (fig. A)
◆
Screw the side handle (2) into one of the
mounting holes in the tool.
Always use the side handle.
Fitting and removing grinding or cutting discs
(fig. A, D - G)
Always use the correct type of disc for
your application. Always use discs with the
correct diameter and bore size
(see technical data). The maximum
thickness for grinding discs is 6 mm,
for cutting discs 3.5 mm.
Fitting
◆
Fit the guard as described above.
◆
Place the inner flange (10) onto the spindle (6)
as shown (fig. D). Make sure that the flange is
correctly located on the flat sides of the spindle.
◆
Place the disc (5) onto the spindle (6) as shown
(fig. E). If the disc has a raised centre (11),
make sure that the raised centre faces the
inner flange.
◆
Make sure that the disc locates correctly on the
inner flange (not for KG70).
SAG.P65
17-07-2001, 14:51
9
Summary of Contents for CD500
