BIRD Thruline 4028A250K Operation Manual Download Page 64

Page: 64 / 65

Thruline RF Power Meter, Model 4421

Customer Service

Any maintenance or service procedure beyond the scope of those in this chapter should be referred to a qualified
service center.

If the unit needs to be returned for any reason, request an Return Material Authorization (RMA) through the Bird
Technologies website. All instruments returned must be shipped prepaid and to the attention of the RMA number.

Bird Service Center

30303 Aurora Road
Cleveland (Solon), Ohio 44139-2794
Fax: (440) 248-5426
E-mail:

[email protected]

For the location of the Sales Office nearest you, visit our Web site at:

http://www.birdrf.com

7/16 Jack, IEC Type 169-4

4240-344

LT-Female

4240-018

LT-Male

4240-012

N-Female

4240-062

N-Male

4240-063

SC-Female

4240-090

SMA-Female

4240-336

SMA-Male

4240-334

7/16 Jack, IEC Type 169-4

4240-344

7/16 Plug, IEC Type 169-4

4240-363

TRU 6934 (F)

4240-371

TRU 7958 (F)

4240-372

Mini UHF-Female

4240-346

UHF-Female

4240-050

UHF-Male

4240-179

1-5/8” EIA Fixed

4240-096

1-5/8” EIA Swivel

4240-208

7/8” EIA

4240-002

TNC-Female

4240-156

TNC-Male

4240-160

Summary of Contents for Thruline 4028A250K


































































Search results

Summary of Contents for Thruline 4028A250K

Reviews:

Related manuals for Thruline 4028A250K

Brands by name

Popular brands

BIRD Thruline 4028A250K, Operation Manual

Search results

Summary of Contents for Thruline 4028A250K

Reviews:

Related manuals for Thruline 4028A250K

Brands by name

Popular brands