manualshive.com logo in svg

BIRD Termaline 8890-300SC13, Operation Manual, Page: 23 / 25

Share
Download
BIRD Termaline 8890-300SC13 Operation Manual Download Page 23

Maintenance

13

Specifications

Replacement Parts

Frequency Range

DC – 28 MHz

Power Rating

2500 W continuous duty

Impedance, Nominal

50 ohms

VSWR

1.1 max

VSWR Stability

< 0.1 dB, from 0 to 100% rated power 
at stability frequency

Stability Frequency

13.56 MHz ± 10 kHz

Connectors

“QC” Type, Female LC normally supplied

Interlock Thermoswitch (Optional)

Normally closed. Opens at 236 °C (457 °F)

Thermoswitch Rating 

115 VAC 
230 VAC

 
10 A 
 5 A

Temperature, Operating

+5 to +40 °C (+41 to +104 °F)

Temperature, Storage

– 40 to +45 °C (–

 

40 to +113 °F)

Altitude

*

* Derate RF power by 2.5% for every 305m (1,000 ft.) above 1,520m (5,000 ft.).

1520 m (5000 ft.)

Humidity

95% noncondensing max

Cooling method

Oil dielectric and convection currents

Dimensions

21.75" L x 7.5” W x 17.25" H 
(551 x 190 x 437 mm)

Weight, Nominal

59 lb. (27 kg)

Finish

Black Epoxy Resin

Description

Qty

Part Number

RF Load Resistor

Resistor O-Ring

1

8890-060
5-230

Clamping band assembly

1

2430-055

Plug 

Vent 
Shipping

1

 
2450-094 
2450-049

Overtemp thermoswitch

Thermoswitch body
Thermoswitch jack

1

8890-008
8890-005
2450-018

Coolant, 2.9 gal (11 liters)

1

5-1070

Radiator assembly

1

2450-313

Access plug 3/4"-14 hex socket

2

5020-103

Summary of Contents for Termaline 8890-300SC13


























Reviews:

No comments