manualshive.com logo in svg

Biostar K8M890-M7 PCI-E, Manual, Page: 3 / 31

Share
Download
Biostar K8M890-M7 PCI-E Manual Download Page 3

K8M890-M7 PCI-E 

1 

CHAPTER 1: INTRODUCTION 

1.1 M

OTHERBOARD 

F

EATURES

 

CPU 

 

Supports Socket 754. 

 

Supports AMD Athlon 64 processor up to 3700+. 

 Supports 

AMD 

Sempron 

processor. 

 

Supports HyperTransport Technology up to 1600MT/s. 

Chipset 

 

North Bridge: VIA K8M890. 

 

South Bridge: VIA VT8237R PLUS. 

Dimensions 

 

Micro ATX Form Factor: 18.99cm (W) x 24.38cm (L) 

Operating System Supporting 

 

Supports Windows 2000 and Windows XP. 

  

Note:

 

Do not support Windows 98SE and Windows ME.

 

Slot 

 

Two 32bit PCI bus master slots. 

 

One PCI-Express x16 slot. 

 

One PCI-Express x1 slot. 

 

One CNR slot. 

On-board IDE 

 

Two on-board connectors support 4 IDE disk drives. 

 

Supports PIO mode 0~4. 

 

Supports Ultra DMA 33/ 66/100/133 Bus Master Mode. 

System Memory 

 

Supports up to 2 DDR devices. 

 Supports 

DDR 

266/333/400. 

 

Maximum memory capacity is up to 2GB. (Following table is 
only for reference.) 

DIMM Socket 

Location 

DDR Module 

Total Memory Size 

DIMM1 128MB/256MB/512MB/1GB 

*1

DIMM2 128MB/256MB/512MB/1GB 

*1

Max is 2 GB. 

Summary of Contents for K8M890-M7 PCI-E
































Reviews:

No comments