Biocare iE 101 User Manual Download Page 29

Page: 29 / 82

Chapter 2 Preparation

User Manual for Electrocardiograph -- 19 --

CAUTION



When the ECG machine is operated together with other medical equipment, please use the accompanying

Equipotential Cable and connect the Equipotential Terminal of the ECG machine altogether with that of the

other equipments so as to protect the animal from possible electric shock due to current leakage from those

equipments.



It is forbidden to connect the Equipotential Cable to a conductive water pipe or other pipes. Otherwise, there

may be hazard of electric shock to the animal.

2.4 Connect to Animal Cable

Figure 2- 3 Connect to Animal Cable

Connect the Animal Cable to the ECG machine.

CAUTION

Do not use any other Animal Cable except that supplied one. The ECG Patient Cable Connector is exclusively

used for connecting the Animal Cable. Do not use it for other purposes.

Summary of Contents for iE 101



















































































Search results

Summary of Contents for iE 101

Reviews:

Related manuals for iE 101

Brands by name

Popular brands

Biocare iE 101, User Manual

Search results

Summary of Contents for iE 101

Reviews:

Related manuals for iE 101

Brands by name

Popular brands