manualshive.com logo in svg

BIO RAD PowerPac Universal Power Supply, Instruction Manual

Share
Download
BIO RAD PowerPac Universal Power Supply Instruction Manual Download Page 33

 

PowerPac Universal Power Supply Instruction Manual 

Page | 25 

4.2.4 Error Messages 

Error Message 

Cause 

Solution 

ERROR STOP: 

CODE 01

 

NO LOAD DETECTED 

CORRECT AND CONTINUE 

RUN PAUSED 

CONTINUE        CANCEL 

1.  Electrophoresis cell 

not connected to the 

power supply, or 

buffer levels too low 

2.  Current load less 

than 2 mA 

1.  Make sure all electrical 

connections make good contact 

and the cables and wire 

electrodes are in good condition. 

Verify buffer levels are 

appropriate. 

2.  Verify the electrophoresis 

application power requirements 

match PowerPac Universal output 

range.  

NOTE:

 The No Load detection 

can be deactivated (see Sections 

3.1

 and 

4.2.3

). 

ERROR STOP: 

CODE 02

 

OVER CURRENT 

CORRECT AND CONTINUE 

RUN PAUSED 

CONTINUE        CANCEL 

Output leads shorted, or 

there is shorting due to 

wrong connections 

Make sure all electrical connections 

make good contact and the cables 

and wire electrodes are in good 

condition.  

Verify buffer levels are appropriate. 

ERROR STOP: 

CODE 03

 

OVER VOLTAGE 

CORRECT AND CONTINUE 

RUN PAUSED 

CONTINUE        CANCEL 

Control circuitry 

problems 

Press the CONTINUE soft key to 

continue the run. If the problem 

continues, cycle power and restart 

the run. If the problem still persists, 

contact Bio-Rad Technical Support. 

ERROR STOP: 

CODE 04

 

WATCHDOG TIMEOUT 

 

 

 

Internal firmware failure   Cycle power and restart the run. If the 

problem still persists, contact Bio-Rad 

Technical Support.  

ERROR STOP: 

CODE 05

 

STUCK KEY 

 

 

 

Key on the front panel 

stuck 

Make sure keypad is not coated with 

foreign substance. Try running 

fingers over keypad to loosen keys. If 

the problem persists, contact Bio-Rad 

Technical Support.  

ERROR STOP: 

CODE 06

 

OUTPUT HIGH 

 

 

 

1.  Attempted restart 

before output has 

discharged 

2.  Very low loading 
 

1.  Wait longer before restarting. 
2.  Check connections for external 

device driving the output. 

If the problem persists, contact Bio-

Rad Technical Support.  

ERROR STOP: 

CODE 07

 

RUN POWER FAILURE 

RUN TERMINATED 

RESET WHEN READY 

RESET 

AC Power interrupted 

during the run and the 

run was terminated 

because the Power 

Failure detection is OFF 

To continue a run after a power 

failure, activate the Power Failure 

Detection mode (see Section 

3.1

). 

Summary of Contents for PowerPac Universal Power Supply











































Reviews:

No comments

Brands by name

Popular brands

Load more brands