Binks Airless 75, Manual

Page: 5 / 40

5
4
SET UP INSTALLATION
Never attempt to assemble, change, or clean the gun, tip, or
tip guard without first relieving pressure from the spray
system. Follow the “ PRESSURE RELIEF PROCEDURE ” in
the sprayer ’ s equipment manual.
Always use tip safety guard for added protection against
injection. Beware that the guard alone will not prevent
injection. NEVER cut off tip guard! Always engage gun
trigger lock when the gun is not in use. Before servicing
equipment, consult all equipment manuals and follow all
warnings.
Do not allow fluid to exceed the fluid manufactures
recommended maximum temperature. Gun must include
heat guard (54-7527) to be used with heated materials.
Note: BINKS Airless Spray Gun Safety Tip Guards for
the 7500 PSI (517 BAR) gun are gray in color.
BINKS Airless 75
PROFESSIONAL AIRLESS SPRAY GUN
7500 PSI (517 BAR) MODEL 0811-7500-1 AND 0811-7500-2
If you are using a genuine BINKS tip, follow the
instructions below to install the guard and tip. If you are using a
different tip, follow the installation instructions provided with the
tip that you are using.
INSTALLATION OF THE TIP AND GUARD
1. Make sure that the tip and tip guard are rated for use at 7500
PSI. (Genuine BINKS parts will be gray in color.)
2. Use seal alignment tool on BINKS
tip handle to insert seal and pressure gasket
into back of guard, turn to align with tip shaft
opening.
3. Insert tip into opening on BINKS
guard.
NOTE: Narrow end of tip handle should be in
forward position for spraying.
4. Thread the guard onto gun head until it stops.
Tighten slightly with wrench
’
DO NOT OVER
TIGHTEN.
CONNECTION TO THE HOSE
Attach a properly grounded fluid hose to the fluid hose
connection fitting (1/4 ’ 18 NPS thread) on the bottom of the
handle of your spray gun. Use two (2) wrenches ’ one on the gun
and one on the hose. Tighten securely.
Follow pressure relief procedure for your sprayer when you stop
spraying and before cleaning, checking or servicing your
equipment.
Tighten all fluid connections before operating equipment.
Check all hoses, tubes, and couplings daily. Replace all worn,
damaged, or loose parts immediately.
EQUIPMENT MISUSE HAZARD
This equipment is for professional use only.
Read and understand all instructional manuals, tags, and labels
before operating equipment.
Use equipment only for its intended purpose. If you are unsure
of its purpose, call your local BINKS distributor.
Misuse can cause death or serious injury.
Do not exceed the maximum working pressure or temperature
rating of the lowest rated system component. See the technical
data in all equipment manuals.
Use fluids and solvents that are compatible with your equipment
wetted parts. See technical data in all equipment manuals.
Read fluid and solvent manufacturer ’ s warnings. For complete
information about your material, request a MSDS from your
distributor or retailer.
Check your equipment daily. Do not alter or modify your
equipment. Repair or replace worn or damaged parts
immediately with genuine BINKS Replacement Parts only.
Do not alter or modify this equipment.
Use equipment only for its intended purpose. Call Binks for more
information.
Route hoses and cables away from traffic areas, sharp edges,
moving parts and hot surfaces.
Do not kink or over bend hoses or use hoses to pull equpment.
Use genuine
BINKS hoses. If provided, do not
remove the spring guards from hoses, these are on the hoses to
prevent rupture from kinking at the connectors.
Keep children and animals away from work area.
Comply with all applicable safety regulations.
Do not operate equipment when fatigued or under the influence
of drugs or alcohol.
TOXIC FLUID HAZARD
Know the specific hazards of the fluid you are using. This
information is on the MSDS for the material that is being used.
Read all fluid manufacturer
’
s warnings.
Store hazardous fluids in approved containers only. Dispose of
all hazardous fluids in accordance with all state, local and
national guidelines.
Wear the appropriate protective clothing, gloves, eyewear and
respirator.
GROUNDING AND ELECTRIC REQUIREMENTS
The sprayer and gun must be grounded. Grounding reduces the
risk of static and electric shock by providing an escape wire for
the electrical current due to static build up or in the event of a
short circuit. Follow the grounding instructions included in the
equipment manual provided with all your spray equipment.
Additional grounding instructions for your BINKS Airless 75
Spray Gun are provided:
Ground your
BINKS Airless 75 Spray Gun through connection to
a properly grounded fluid hose and pump.
Safety
Guard
Trigger Lock
Trigger
1/4 - 18 NPS thread
MOdEl 0811-7500-1, 0811-7500-2, 0811-7500-3