Binder 9010-0269 Operating Manual Download Page 10

Page: 10 / 69

FDL (E2) 03/2011

page 10/68

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in moderate or minor (re-
versible) injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in damage to the product
and/or its functions or of a property in its proximity.

1.2.2 Safety alert symbol

Use of the safety alert symbol indicates a

risk of injury

Observe all measures that are marked with the safety alert symbol in order to avoid death or
injury.

1.2.3 Pictograms

Warning signs

Electrical hazard

Hot surface

Explosive atmosphere

Tipover hazard

Inhalation hazard

Pollution Hazard

Harmful substances

Biohazard

Mandatory action signs

Mandatory regulation

Read operating

instructions

Disconnect the power

plug

Lift with several persons

Environment protection

Prohibition signs

Do NOT touch

Do NOT spray with

water

Information

to be observed in order to ensure optimum function of the product.

Summary of Contents for 9010-0269






































































Search results

Summary of Contents for 9010-0269

Reviews:

Related manuals for 9010-0269

Brands by name

Popular brands

Binder 9010-0269, Operating Manual

Search results

Summary of Contents for 9010-0269

Reviews:

Related manuals for 9010-0269

Brands by name

Popular brands