Icarus 1210 System
USER GUIDE
OFFHOOK light
This comes on when Line
is off HOOK
Off when on HOOK
PHONE button
Press to begin or answer a
telephone call.
Press to hang up at the end
of a call.
PLAY / MSG button
VOLUME button
Press during a call to
adjust the volume.
INT ( ) button
Press and Hold over 2
second for Intercom
Call.
CHARGE lights
This comes on when
thehandset batteries are
being charged.
SPEAKERPHONE button
Press to turn the
speakerphone on and off.
MEMORY button
Press to make calls to
numbers stored in memory
R (Recall) button
Direct Message Play
You may need this during a
call if your Icarus 1210 is
connected to a PBX, or if
you use BT Select
Services
PROG / LNR button
When on hook, press to start
programming.
When off hook, press for Last
Number Redial
HANDSET LOCATOR
button
Press this to make the
handset ring, to help you
find it if you
’
ve forgotten
where you put it.
1 Installation
You need
one battery pack (NiMH, 3.6v, 300mAh)
for each handset.
To fit the batteries
1 Open the battery
compartment cover.
2 Insert the plug in the
connector, as shown.
Tuck the wires in and lay the
battery pack in the
compartment
3 Fit the battery compartment
cover, sliding it into place
and pressing firmly to make
sure it is secure
Warnings
Dispose of used batteries safely
never try to burn them
or put them anywhere they could get burnt or punctured.
When you are not going to use your Icarus 1210 for a few
weeks,
take the batteries out
so they do not leak
corrosive substances.
Do not leave dead batteries in your handset
they might
leak if you do.
2 Making and answering calls
To make a call
To answer a call
To redial the last number
To end a call
Press
PHONE
or
SPEAKER PHONE
Key in the telephone number
When the handset and base unit ring, press
PHONE
or
SPEAKER PHONE
Press
PHONE
or
SPEAKER PHONE
Press
LNR
Press
PHONE
or
or
or
or
or
or
1
2
1
1
2
Earpiece Volume
To store a number
To make a memory call
During a phone call, press
VOL
to cycle through the
different earpiece volume settings.
On Hook Stage
Press
MEM
Offhook indication LED blinks slowly
Key in the memory location (0 to 9)
Press
MEM
again
Key in the number (key *,#,0~9, up to 20digits) you
wish to store
Press
MEM
again
Confirmation Tone or Error Tone
Off Hook Stage
Press
MEM
Offhook indication LED is blinking slowly
Key in the memory location (0 to 9) that you want to
dial
Dials out the stored number. [No confirmation tone.]
An Error Tone is heard if the memory is empty.
3 Memory dialing
1
2
3
4
5
6
7
1
2
3
4
To delete a stored number
Dial Mode Setting (P/LNR button function and code * 2 2)
On hook stage
Press
MEM
Offhook indication LED blinks slowly
Key in the memory location (0 to 9)
Press
MEM
again
Press
MEM
again
Confirmation Tone or Error Tone
Offhook indication LED is OFF
On hook stage
Press key
P/LNR
Offhook indication LED blinks slowly
Press digits
2 2
Confirmation Tone
Press DTMF mode, or
#
Pulse mode
Press key
P/LNR
Confirmation Tone
1
2
3
4
5
6
7
1
2
3
4
5
6
7
4 Program operation
Press
P/LNR
key
Key in digits
3 1 1
Melody On
Press to increase the volume
Press
#
to decrease the volume
Press P/LNR key to confirm setting
Confirmation Tone
Change handset ringer volume
1
2
3
4
5
6
7
Press
P/LNR
key
Key in digits
3 1 2
Melody On
Press button 0~9 to select melody
Press
P/LNR
key to confirm setting
Confirmation Tone
Change handset ringer melody
1
2
3
4
5
6
On Hook Stage
Press and Hold
/INT
key
You hear the internal call dial tone
Press handset number
Ringback tone can be heard
Called Handset is ringing
Intercom Calll ( /INT button function )
1
2
3
4
5
6
Press the
P/LNR
button then key in digits
2 1 1
Melody is on
Press the button to increase the volume up to volume
level 5
Press the
#
button to decrease the volume down to level 1
or to turn the base ringer off (level 0)
Press
P/LNR
button to confirm
A confirmation can be heard
Base melody volume
1
2
3
4
5
6
Press the
P/LNR
button then key in digits
2 1 2
Melody is on
Press button 1~5 to select melody
Press
P/LNR
to confirm
A confirmation tone can be heard
Base melody
1
2
3
4
5
When the battery level is low during a call, you will hear the low battery
tone in the earpiece every minute.
Low battery tone
When the handset goes out of range of the base unit, you will hear the
Out of Range Tone in the earpiece every 12 seconds. You must return in
range of the base soon otherwise the call will be dropped.
Out of range
Binatone Help Line:
0845 345 9677
(Local Call rate)
Binatone Help Line:
0845 345 9677
(Local Call rate)
Binatone Help Line:
0845 345 9677
(Local Call rate)
Binatone Help Line:
0845 345 9677
(Local Call rate)
Binatone Help Line:
0845 345 9677
(Local Call rate)
Binatone Help Line:
0845 345 9677
(Local Call rate)
Binatone Help Line:
0845 345 9677
(Local Call rate)
Binatone Help Line:
0845 345 9677
(Local Call rate)
Binatone Help Line:
0845 345 9677
(Local Call rate)
Reset the System
HS on hook stage
Press key
P/LNR
Offhook indication LED is blinking slowly
Key in digits
4 2 1 0
Wait until you hear the confirmation tone from HS and BU
Both HS and BU are set in default setting
1
2
3
4
5
6
Call Transfer ( /INT button function)
Off hook stage
Press and hold
/INT
to transfer a call.
You will hear internal dial tone in the earpiece and the
caller will be on hold.
Press Handset number for the call transfer
Hear internal ring back tone
Once Connected with second handset
Press
PHONE
key to transfer and hang up
OR - press and hold
INT
key to reconnect to the caller
1
2
3
4
5
6
What
’
s the
TONE
mean ?
Confirmation Tone :
( =__== ) two short
beeps
Error Tone :
(======) One long beep
Low battery Tone :
(==) single beep with
long pause (1 mins)
Out of range Tone :
(==) single beep
with long pause (12 seconds)
Where is the
Handset number
?
1
Handset
number
Special error tone
If you try to operate an empty memo during online stage, there
will be a special error tone heard.
RED
BLACK
Leave the handset on the
charging cradle for 15 Hours
To Re-register handsets
First de-register all handsets
Obtain all handsets for the operation
Start register handset from handset number 1 with
the following setps:
Press and hold the Base Page key for 4 seconds until it
gives a double beep. The base will then be in
registration mode for 20 seconds.
Put Handset On Hook Stage
Press key
P/LNR
Offhook indication LED is blinking slowly
Press digits 1 1
Confirmation tone
Press base number (1,2,3,4)
Handset and Base in registration communication
Confirmation Tone or Error Tone
Repeat 1-12 for handset number 2~4 If multiple
handset systems in sequence.
1
2
3
4
5
6
7
8
9
10
11
12
13
Remove Base power
Press and hold the Page key.
Reconnect the Base power.
Wait until you hear 4 double beeps.
Release the Page key.
After a short time you will hear a confirmation tone.
Now, all the registrations are removed from your base
De-register all handsets from a Base
1
2
3
4
5
6
7
WARNING: Your phone have been registered before ship - you doesn't
need to register nor de-register normally
