background image

UPSI-2406DPx

Revision 1-5

27

CONNECTOR

PART NO.

COUNTERPART NO.

V

IN

/V

OUT

Würth Elektronik 691325310004 Würth Elektronik 691364300004

RL

Würth Elektronik 691305140002 Würth Elektronik 691304130002

USB

Würth Elektronik 61400416121 

USB type B connector

RS232

D-Sub9 Female

D-Sub 9 Male

F7  Overview connector / counterpart with description / Scope of delivery

SCOPE OF DELIVERY

QUANTITY

DESCRIPTION

1x device

UPSI-2406DP1 or UPSI-2406DP2 or UPSI-2406DP3 - DC UPS

1x

V

IN

 / V

OUT

 connector counterpart

1x

Relay connector counterpart

F8  Charging time

Charging times depend on energy storage, input voltage and the load current.

F9  Reverse polarity / Overload / Short circuit

Reverse polarity:
The device has active reverse polarity protection at the input if the input terminal is connected with reverse 
polarity while the device is still switched off (e.g. during commissioning). If the device operates in battery mode 
and the input terminals are connected with reverse polarity, no reverse polarity protection is given.

Overload:
If the load current at the output is too high, the device switches it off. For maximally allowed current values 
and peak current values refer to chapter D „Technical Data”. The status LED indicates the error status by means 
of a very rapid flashing sequence. A restart attempt occurs every 10 seconds in normal mode. During battery 
mode there is no restart attempt. 

Short circuit:
In the event of a short-circuit at the output of the UPS, the output is immediately disconnected (<5 ms). The 
status LED indicates the error status by means of a very rapid flashing sequence. A restart attempt occurs every 
second in normal mode (non-latch). During battery mode there is no restart attempt. The impact of a short- 
circuit to the device depends on length and diameter (impedance) of the output wiring. In case of a short-circuit 
directly at the plugs a damage of the device can occur.

Summary of Contents for UPSI-2406DP Series


































Reviews: