BHI HydroRam HK300S Operations Manual & Parts List Download Page 3

Page: 3 / 51

BHI

Best Hammer Industries

INDEX

Ⅰ. INTRODUCTION ----------------------------------------------------------

Ⅱ. SAFETY PRECAUTION -----------------------------------------------------

1. Safety Decals -------------------------------------------------------------------- 2

2. Installation of Hammer -------------------------------------------------------- 4

3. Before Operation --------------------------------------------------------------- 5

4. Serial number marking position ------------------------------------------------ 5

5. Tool Replacement ------------------------------------------------------------- 5

6. Hammer Operation ------------------------------------------------------------- 6

Ⅲ. WARRANTY --------------------------------------------------------------

1. Delivery record ----------------------------------------------------------------- 9

2. Claim application under warranty ------------------------------------------ 10

Ⅳ. TECHNICAL DATA --------------------------------------------------------

1. Standard Specifications -------------------------------------------------------- 11

2. Principles of Operation --------------------------------------------------------- 12

3. External Dimension - Power cell and Bracket ------------------------------ 14

4. Construction - Excavator & Hammer Bracket ------------------------------- 15

5. Torque Chart --------------------------------------------------------------------- 16

6. Blow Speed & Power Control-----------------------------------------------

Ⅴ. OPERATION AND HANDLING OF HYDRAULIC HAMMER ------------

1. Hammer ------------------------------------------------------------------------ 17

2. Rules to Remember ------------------------------------------------------------

3. Operator's Routine Maintenance --------------------------------------------- 23

4. Periodic Maintenance ---------------------------------------------------------

5. Factors of Tool Life ------------------------------------------------------------- 24

6. N

Gas Pressure Maintenance ------------------------------------------------ 26

7. Nitrogen Gas Charging Pressures Table ------------------------------------- 28

8. Maintenance of Oil Filter ----------------------------------------------------- 29

9. Hydraulic Oil & Grease ------------------------------------------------------ 30

10. Maintenance Checking Schedule --------------------------------------------- 31

Ⅵ. TROUBLE SHOOTING -----------------------------------------------------

Ⅶ. ACCESSORY PARTS LIST -------------------------------------------------

1. Tool type and parts list -------------------------------------------------------- 34

2. Union cap parts list --------------------------------------------------------------

3. Hose plug parts list --------------------------------------------------------------

4. O-ring adapter part list ----------------------------------------------------------

5. B

ase cover plate dimension -

-------------------------------------------------

Ⅷ. UNDERWATER KIT(OPTION)

------------------------------------------------

Ⅸ. AUTOLUBE KIT(OPTION) ------------------------------------------------

Ⅹ. WEAR PARTS AND JUDGMENT TOOL

------------------------------------- 39

Ⅺ

. PARTS LIST

----------------------------------------------------------------------- 41

Summary of Contents for HydroRam HK300S




















































Search results

Summary of Contents for HydroRam HK300S

Reviews:

Related manuals for HydroRam HK300S

Brands by name

Popular brands

BHI HydroRam HK300S, Operations Manual & Parts List

Search results

Summary of Contents for HydroRam HK300S

Reviews:

Related manuals for HydroRam HK300S

Brands by name

Popular brands