Betta 6000 Installation Manual Download Page 1

 

 

Installation Guide for Betta 6000 Straight Drop Awning  
with Side Channels with Brackets 

 
Please Note: These instructions should be read thoroughly before installing. 

 

This  is  a  guide  to  assist  in  the  installation  and  care  of  your  external  awnings.  Betta  Blinds  and  Awnings  do  not 
guarantee the accuracy of the information contained in this guide. We recommend an experienced expert installer 
to rely upon their own skills. This is based on general knowledge concerning the assembly, materials and working 
process of  the external  blinds,  which  is  known  to  us at  the  time  of  printing  this guide,  consequently,  is  subject  to 
change and Betta Blinds and Awnings specifically reserves the right to change this guide without notification. 

 

Ensure all components are included in your packaging, before proceeding to install: 

 

  Gearbox 

(if required)

 

  Nut and bolt 
  Crank handle 

(if required)

 

  Awning 

 

  Pivot pin and plate with nut and bolt 
  Lock in pins x 2 
  Side  channels  x  2  (make  sure  this  has  felt 

inserted inside channel) 

  Snap in front cover strip (face fit only) 

 

You will also need:  screws, plugs, Philips head screwdriver, drill, hammer drill (if drilling into concrete), measuring 
tape, spirit level, 18mm drill bit and dyna bolts (if required) 
 

 

If installing on a brick wall NEVER put the screw into a mortar line.

 If the position, you need to drill is over a 

mortar line move up to the centre of the brick above that position. 

 

Check the size of your blind against the label, which will be attached to the packaging, or it could be on the blind. 

 

 

1. 

FACE FIT,

 attach the side channel with the snap in recess facing outwards.  Pre-Drill holes through in-fill part 

of the channel. Place channel against post/wall and mark holes  

 

2.  Pre-drill  all  holes  and  plug  if  needed.  When  all  holes  are  drilled,  position  the  channels,  and  fasten  with 

appropriate fixings. Repeat these steps for other the channel. 

 

3. 

REVEAL FIT,

 attach the side channel to the inside of the post/wall, with the snap in recess facing backwards. 

Pre-Drill holes through the channel. Place channel against post/wall and mark holes  

 

4.  Pre-drill  all  holes  and  plug  if  needed.  When  all  holes  are  drilled,  position  the  channels,  and  fasten  with 

appropriate fixings. Repeat these steps for other the channel 

 

5.  Slide lock in pins into bottom rail.  The pin must face outwards, towards the channel. 

 

6.  If required attach Install the pivot pin into the end of the blind and plate to the idle end bracket, using nut and 

bolt provided. 

 

7.  If  required  attach  gearbox  to  bracket,  using  nut  and  bolt  provided.    The  gearbox  can  be  positioned  in  two 

different angles.  Betta Blinds recommend the gearbox to be angled outwards for ease of use. 

NB: Bolt from 

the outside in.

 

 

8.  Hang  the  awning.  The  motor  end  /  crank  end  (square  tube  end)  goes  in  first.    Drop  the  other  end  onto  the 

slotted part of the pin. Secure this end with the split pin supplied.  

 

Summary of Contents for 6000






Reviews: