background image

WALL ANCHORING INSTRUCTIONS

INSTALLATION RECOMMENDATIONS

Wood Screw — VR-1125 

3 1/2 in (89 mm)

“Adjustable wall anchor” Snaptoggle® *

Use for metal stud

1

2

3

Locate stud centerlines using electronic stud finder. Use pencil to mark stud centerlines 
below part 87.

Drill a 1/8 in or 3 mm pilot hole into the wall stud to determine the type of wall 
structure present.

Wood found behind the wall board?

a.  Use a 1/8 in drill for the pilot hole on the plywood rail. 
b.  Use the wood stud mounting approach with the six #10 x 3.5 in wood screws provided.

4

Metal found behind the wall board?

a.  Use a 1/4 in drill for the pilot hole on the plywood rail and a 1/2 in drill for the wall.
b.  Use the metal stud mounting approach with the six #10 x 3 in toggle bolts.

Concrete Screw

3/16 in (5 mm) diameter x 3 1/4 in (83 mm)

5

Concrete found behind the wall board?

a.  Use a 5/32 in masonry drill for the pilot hole on the plywood rail and for the wall.
b.  Use the masonry wall structure mounting approach with the six #10 x 3.25 in concrete screws.

WARNING

AVERTISSEMENT

ADVERTENCIA

IMPACT or CRUSHING HAZARD: if bed is not 
properly attached to the wall, it can suddenly 
fall, resulting in serious injury or death.

•  For wood, metal, or masonry wall structure, a 
  qualified person must install the bed to the wall.

•  For all other wall types, a construction 
  professional must install the bed to the wall.

•  The choice of wall attachment screw depends on 
  wall type. Use wall attachment screws suitable 
  for your wall material.

•  Verify structural integrity of floor and wall prior 
 to 

installation.

•  Only attach wall bed to wood stud, steel stud, 
  or masonry wall structure.

•  NEVER use hollow wall anchors.

•  ALWAYS use 12 screws for floor and wall 
 attachment.

RISQUE DE CHOC ou D’ÉCRASEMENT : si le lit n’est pas 
correctement fixé au mur, il peut tomber subitement 
entraînant des blessures graves ou la mort.  

•  Pour les structures murales en bois, en métal ou en 
  maçonnerie, une personne qualifiée doit fixer le lit au mur.

•  Pour tous les autres types de murs, un professionnel 
  de la construction doit fixer le lit au mur.

•  Le choix de vis de fixation murale dépend du type de mur. 
  Utilisez des vis de fixation murale adaptées au matériau 
 de 

votre 

mur.

•  Vérifiez l’intégrité structurale du plancher et du mur 
 avant 

l’installation.

•  Fixez seulement le lit escamotable à des montants de bois, 
  de métal ou à une structure murale en maçonnerie.

•  N’utilisez JAMAIS de chevilles pour cloison sèche.

•  Utilisez TOUJOURS 12 vis de fixation murale.

IMPACTO o PELIGRO DE APLASTAMIENTO: si la cama no 
está bien fijada a la pared, puede caer repentinamente, 
provocando lesiones graves o la muerte.

•  Para las estructuras de madera, metal o mampostería, 

una persona cualificada debe instalar la cama a la pared.

•  Para todos los demás tipos de paredes, un profesional 
  de la construcción debe instalar la cama a la pared.

•  La elección del tornillo de fijación a la pared depende 
  del tipo de pared. Utilice tornillos de fijación a la pared 
  adecuados para el material de la misma.

•  Verifique la integridad estructural del suelo y la pared 
  antes de la instalación.

•  Fije la cama a la pared sólo a una estructura de 
  madera, acero o mampostería.

•  NUNCA utilice anclajes de pared huecos.

•  SIEMPRE utilice 12 tornillos para la fijación al suelo 
  y a la pared.

85183-2  AN

22

SERVICE: 1-888 8BESTAR (1-888 823-7827)

Summary of Contents for 85183-2

























































Reviews: