background image

Should you need more information concerning the warranty, do not call to the place 
of purchase. Please call our customer service department for immediate assistance 
using the toll free number below. Please have your assembly instruction manual on 
hand when you call. 

BESTAR products are warranted to the original purchaser against defects in material 
or workmanship in the furniture. Defects as mentioned in this warranty refer to any 
imperfections which may impair the use of the product. Our warranty is expressly 
limited to the replacement of furniture parts and components for the time specified 
in the product description and following the date of purchase. BESTAR will replace 
any part that is defective. This warranty applies under conditions of normal use. 
Our furniture products are not intended for outdoor use, except those in the Outdoor 
Collection. The warranty does not cover labor or assembly costs or defects caused by 
improper assembly or disassembly, after-purchase product modifications, intentional 
damage, accidents, or exposure to the elements. Bestar reserves the right to request 
a proof of purchase to document a warranty claim. In no event shall BESTAR be liable 
for incidental or consequent damages resulting from the misuse of the product. 
This warranty is not transferable and is valid only in Canada and the United States 
excluding Alaska, Hawaii and Puerto Rico.

Warranty Information

www.bestar.com/warranty

Summary of Contents for 85183-2

























































Reviews: