Best WI-Q MERCURY Setup And User Manual Download Page 28

Page: 28 / 50

28 | Wi-Q™ Mercury Setup and User Guide

3 HARDWARE INSTALLATION

NOTE:

Radio 1 PAN ID can be edited when in Mercury Mode. PAN

IDs only need to be changed if there is a conflict with multiple
Gateways within RF range of each other. Editing Radio 1 PAN ID
will also change Radio 2 PAN ID. Each Gateway uses up to 66 PAN
IDs.

• Radio 2 Channel – The channel assigned to Wi-Q Radio 2.
• Radio 2 PAN ID – The Personal Area

etwork ID assigned

to Wi-Q Radio 2.

3.2.5.3.1.1 Wireless Controllers

At the bottom of the Gateway Status window is a list of the
associated Wi-Q Controllers and their attributes.

• ACR ID – The Reader ID when the portal is in Mercury

Mode with the LP4502 Access Control Board. This field will
be blank when Mercury Mode is not in use.

• MAC Address – The Reader’s unique Media Access Con-

trol address that uniquely addresses the device on the
network.

• Radio Channel – The channel the door controller is com-

municating on with the Gateway.

• Associate Time – The date and time the Wi-Q Door Con-

troller associated with the Gateway.

• Last Beacon Time – The last date and time the Wi-Q

Door Controller beaconed information up to the Gateway.

• Pending Operations – Progress percentage of pending

messages from the door controller to the Gateway.

3.2.5.3.1 Details

• IP Address – Displays the Ethernet IP address of the

Gateway as configured in its current state.

• MAC Address – The Gateway’s unique Media Access

Control address that uniquely addresses the device on the
network.

• Time of Last System Reboot – The last date and time the

Gateway was reset, or power cycled.

• Current Sign-on Key – A 6-digit sign-on key associated

with the segment the Gateway is associated with.

• Associated Controllers on Gateway – Displays the num-

ber of controllers communicating with the Gateway when
the view was initially displayed.

• Wi-Fi IP Address – IPv4 address assigned to the Wi-Fi

radio on the Gateway.

• Wi-Fi SSID – The Gateway’s wireless network name. This

is always Wi-Q followed by the last six characters of the
device’s unique MAC address.

• Radio Channels Allowed – The channels currently en-

abled on the Gateway to connect to the Wi-Q Controllers.

• Radio 1 Channel – The channel assigned to Wi-Q Radio 1.
• Radio 1 PAN ID – The Personal Area Network ID assigned

to Wi-Q Radio 1.

Summary of Contents for WI-Q MERCURY



















































Search results

Summary of Contents for WI-Q MERCURY

Reviews:

Related manuals for WI-Q MERCURY

Brands by name

Popular brands

Best WI-Q MERCURY, Setup And User Manual

Search results

Summary of Contents for WI-Q MERCURY

Reviews:

Related manuals for WI-Q MERCURY

Brands by name

Popular brands