12
13
• The child seat MUST NOT be installed in a front
passenger seat WITH AN ACTIVATED AIRBAG.
• The floor support must always be used. Make sure that the
floor support is fully pushed down and that the seat is positioned
horizontal with the spirit level in the middle.
• Never drive with a child in the seat if the seat is rotated to the side.
• Make sure the indicators are green before you drive.
! Warning: potential misuse
• Do take care when you remove the cover, as re-fitting the cover is
done in reverse.
• The cover of the headrest can be taken off separately by
disconnecting the beads at the back and pulling off the fabric
towards the front.
protection in the side impact still further. (Not on all models) (6)
18. Tip: For an optimal height of the SIP+, position it between the two
raised dots on the side of the seat shell.
19. Do not use the SIP+ on the seat when the space between seat and
door of the vehicle is too small, which might lead to a situation
where the seat is not positioned correctly on the vehicle seat.
Removing and refitting the cover
Baby insert
Baby cushion
1. The baby insert must be used from birth and can be used until a
stature height of 87 cm. Don’t take the baby insert out before the
baby can sit upright by itself.
2. The baby insert can be taken out of the seatshell, by guiding the
harness through the slots of the baby insert.
3. The baby insert can be positioned back in the seatshell, by guiding
the harness through the slots of the baby insert. Use the baby insert
only in the most reclined position of the seat. Make sure the harness
is positioned correct, so the harness can be pulled tight without
twisting. (15)
1. The baby cushion offers extra comfort for young babies.
2. < 60 cm (16)
3. > 60 cm (17)
1. Turn the seat towards the door while you pull the rotation release
handle upwards.
2. Check that the shoulder strap slots are level with your child’s
shoulders. (7)
3. While pressing the button of the central adjuster, pull the shoulder
straps away from the seat with a flat hand. Make sure to pull the
straps evenly so that they stay at the same length. (8)
4. Open the harness buckle. (9)
5. The height of the shoulder straps and the headrest can be adjusted
by pulling the release handle upwards at the back of the headrest and
pulling the headrest up or down. (10)
6. Position the shoulder straps over the marking at the sides of the seat
to use the magnets to keep the harness open while you position the
child. (11)
7. When the child is positioned, place the shoulder straps over the child’s
shoulders and close the buckle: CLICK! (12)
8. Pull the harness strap through the central adjuster in the direction of
the arrow straight up/forwards. Continue pulling until the harness
is a comfortable but a firm fit. (13)
9. Turn the seat against the driving direction before driving and check if
the release handles show green and the seat is locked into the driving
direction. (14)
Positioning of the child
1. To remove the seat from the vehicle, turn the seat rear facing
and push the seat upwards while adjusting the floor support to its
shortest length.
2. Release the ISOfix connectors out of the seat by pushing down
the switch for the ISOfix connectors on both sides. Pull the ISOfix
release switch on both sides to disconnect from the ISOfix car
anchorage.
Removal of the seat from the vehicle
Summary of Contents for iZi Twist B i-Size
