33
82.490 - Raptor
- To totally drain the tank:
With the
C-TRONIC
control box
(figure 7, page 28):
▪ Press the
key next to the
icon.
With the
-PILOT
mutifunction joystick
(figure 9, page 29):
▪ Press the key (6) of the
-PILOT
joystick.
- Then, to close the spraying:
With the
C-TRONIC
control box
(figure 7, page 28):
▪ Press the
key next to the
icon.
With the
-PILOT
mutifunction joystick
(figure 9, page 29):
▪ Press the key (6) of the
-PILOT
joystick.
- Lower the switch (4) (figure 8, page 29) to reduce the engine speed.
- Press the push-button (3) (figure 8, page 29) to stop the pump drive.
PHASE 4 - FINAL RINSING OF THE SPRAYER
IN A RECOVERY AREA AT THE FARM
•
Fill the rinsing tank with the clear water.
•
Open the main tank's drain valve (figure 2, page 25).
With the pump off.
RINSING THE MAIN TANK USING THE RINSING TANK
•
Spray circuit closed, put the indexes on Berlogic function
.
(DUALELEC option, choose function
06-
).
- Engage the pump's hydraulic drive by pressing push-button (3) (figure 8, page 29).
- Bring the engine speed up to at least 1,200 rpm by raising switch (4) (figure 8, page 29).
RINSING THE INCORPORATION HOPPER CIRCUIT
•
Place the index (1)
(figure 11, page 30)
on Berlogic function
.
(DUALELEC option, choose function
04-
).
RINSING THE MIXING CIRCUIT
•
Place the index (1)
(figure 11, page 30)
to position
to begin the mixing.
(DUALELEC option
, perform 2 short pressings of the
key on the
C-TRONIC
control box to activate the
manual mixing, then adjust it on 100 %
(see manual No. 82.510)
.
RINSING THE BOOM
•
Put the indexes on Berlogic function (DUALELEC option, choose function
08-
).
- Open the spraying:
With the
C-TRONIC
control box
(figure 7, page 28):
▪ Press the
key next to the
icon.
With the
-PILOT
mutifunction joystick
(figure 9, page 29):
▪ Press the key (6) of the
-PILOT
joystick.
- Engage the pump's hydraulic drive by pressing push-button (3) (figure 8, page 29).
- Bring the engine speed up to at least 1,200 rpm by raising switch (4) (figure 8, page 29).
- Spray the residues on the recovery area.
Repeat the operation if residues remain.
Note:
When finished spraying or between 2 successive applications of different products, it is
recommended that the outside of the sprayer be cleaned (see procedure page 40).
Summary of Contents for RAPTOR 2540
