Fountain
Base
Water
Tube
Dancing
Water
Attachment
Fountain Top With
Battery Compartment
& Water Pump
CONTENTS:
Assembly
Water
Pump
Battery
Compartment
(4 1.5v AA
Batteries
Not Included)
Water Pump
Tube
Max Water Level
(Upper
Decorative
Ring)
Battery
Compartment
Screws x2
Start/Stop
Button
Locating Dowls
Alignment
Notch
Bowl
(Not Included)
Minimum
Water
Level
Fountain
Base
Fountain
Top
Dancing
Water
Attachments
Alignment
Notch In
Base
Recommended minimum bowl size
is approximately 6 inches
Diagram 1a:
O W N E R S M A N U A L
Piccolo Fountain Tower
TM
INSTALLING BATTERIES:
1. Lift Fountain Top with Battery Compartment & Water
Pump out of the Fountain Base (Figure 5). Disconnect
the Water Tube from the Battery Compartment.
2. Unscrew (counter clockwise) the Battery Compartment
Screws and open cover (Figure 1a, 1b).
3. Orient the Battery Compartment with locating dowel on top.
(See Arrow Figure 2a& 2b).
4. Insert 2-1.5v AA Batteries with the (+) side facing up in
Battery Compartment and 2 AA Batteries with the (-) facing up in
Battery Compartment (Figure 2a).
5. Reinstall the Fountain Top by aligning the locating dowel in
the Battery Compartment and Fountain Top. Set the Battery
Cover down onto the Battery Compartment ensuring the dowel
sets into the alignment hole. Tighten the Battery Cover Screw by
turning clockwise. NOTE: You may need to apply pressure to
the Battery Compartment Screws while tightening for the
threads to catch.
1. Take the Fountain Top/Battery Compartment and Water Pump, connect one side of the Water Tube to the Water Pump and the other end to the bottom side of the
Battery Compartment (A & B of Figure 4).
2. Find a suitable bowl and place it on a flat, level surface and place the Fountain Base, without the Fountain Top with Battery Compartment and Water Pump, into
the center of the bowl.
3. Lower the Fountain Top with Battery Compartment and Water Pump into the Fountain Base. There are two locating dowels and two alignment notches that help
you align the Fountain Top to the Fountain Base. Fit these into place and press to Fountain Top and Base together to secure(Figure 6).
4. Fill bowl with water, water level should cover the Water Pump (Diagram 1a).
OPERATING YOUR FOUNTAIN TOWER:
Turn On Fountain: When the Fountain is off, press the button to turn on (Figure 7a & b). The fountain will run for one hour and automatically turn off.
Stop Fountain: To stop the Fountain press the button to turn off.
DANCING WATER ATTACHMENT (OPTIONAL): When Fountain is not running, attach the Dancing Water Attachment and attach to the outlet in the middle of the
Fountain Tower (Figure 8a, 8b and 8c). To prevent overspray, use a larger bowl.
*PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO ASSEMBLE YOUR NEW FOUNTAIN
Figure 6
Figure 5
Figure 1b
Figure 1a
Figure 3b
Figure 2b
Figure 4
A
B
Figure 3a
Figure 2b
STEP
2.
STEP
3.
STEP
Figure 2a
CHANGING BATTERIES:
1. Remove any Dancing Water Attachment, lift Battery
Compartment and Water Pump out of the Fountain (Figure 5),
ensure Battery Compartment and Water Pump are completely
dry before opening Battery Compartment. It is important that
no water enters the Battery Compartment.
2. See Installing Batteries Section above on how to reinstall
batteries and reassemble.
3. Set the Battery Compartment and Water Pump back into the
Fountain (Figure 6).
Figure 7b
Figure 7a
Button
Button
Need Help?
Call us for assistance at:
+1 (619) 449-2392
or you can email us at:
customercare@
berninifountains.com
For video tutorials visit:
berninifountains.com/support
Our Customer Care Department is available:
Monday - Friday 8:30am to 4:00pm PST
11:30am - 7:00pm EST
Locating
Dowel
Locating
Dowel
Alignment
Notch in
Battery
Housing
Alignment
Notch in
Fountain
Top
Alignment
Notch in
Battery
Housing
Alignment
Notch in
Battery
Housing
Alignment
Notch in
Fountain
Top
Battery Compartment
Retaining Screws X2
Battery Compartment
Retaining Screws X2
Battery Cover
Retaining Nut
Battery Cover
O-Ring
Battery Cover
Retaining Nut
Battery Cover
O-Ring
Battery Cover
O-Ring
Dancing Water Attachment
Figure 8a
Figure 8b
Figure 8c
Note: Minimum bowl size is 6 in. It is
recommended that the Dancing
Water Attachment be used outdoors.
To prevent over spray use a larger bowl.
Please note, images of parts
are not to scale with one another.
Battery Cover
O-Ring
