Berker 75310002 Page 9 Technical Documentation Manual Download

Page: 9 / 174

Switch/shutter actuator 8/4gang 16A RMD
75318003
Switch/shutter actuator 16/8gang 16A
RMD
75310002

Technical

Documentation

Version: 04.04.2007

Part 5

(Subject to prior change)

75310002.doc

Seite: 9 / 174

Connecting the device for electrical loads in the switching mode

In the switching mode, the outputs can be controlled independently of one another.

The switching/shutter actuator must have been programmed in ETS for switching operation of the
corresponding output channel (2 x switching output).

Connect the loads and the bus line as shown in fig. 3 (connection example).

Fig. 3: Electrical connection for loads in switching mode

Observe the admissible load ratings (cf. 'Technical data').

The device can be used with different phase conductors (L1, L2, L3).

Do not connect three-phase AC motors to the actuator.

Summary of Contents for 75310002















































































































































































Search results

Summary of Contents for 75310002

Reviews:

Related manuals for 75310002

Brands by name

Popular brands

Berker 75310002, Technical Documentation Manual

Search results

Summary of Contents for 75310002

Reviews:

Related manuals for 75310002

Brands by name

Popular brands